Latest Starter Tenders in Military Engineer Services
Find the latest starter tenders in military engineer services for 2026 from government departments, corporations and state PSUs. Get tender details and bidding information.
FILTERS
Category: Starter
Organization: Military Engineer Services
22 Live Starter Tenders in Military Engineer Services 2026
T247 ID-103788401 |Bid Value:₹ 65.00 Lakh |EMD:₹ 1.23 Lakh |24-09-2026 5 Days Left
dismantling taking down centrifugal pump set from platform and disconnecting suction delivery pipe line electrical connections transport the same to workshop for repairie machine work welding grinding turning polishing lathe work filler work etc complete as required on site and after repairing transporting the pump set from workshop to site installation at site connecting suction delivery pipe and electrical connection complete all as directed by engineer-in-charge for 120 hp capacity pumps note- i the quoted rate shall deemed to be inclusive of the cost of providing foundation nuts bolts washers gland packing greasing oiling and oil sheet gasket ii the spare parts shall be measured and paid separately under relevent items of this boq no extra payment will be made to the contractor for any additional requirement for fixing reinstalling the pump motor set iii gland packing greasing and oiling shall be changed at the time of repairs, all as per item no 1 above but 100 hp, all as per item no 1 above but 75 hp, all as per item no 1 above but 5040 hp, all as per item no 1 above but 30 20 hp, all as per item no 1 above but 12515hp, all as per item no 1 above but 1075 hp, all as per item no 1 above but 5 3 25 hp, material and labour for disconnecting the motor by delinking the centrifugal pump set transporting to workshop opening the motor removing the unserviceableburnt windings from the motor stator cleaning the stator slots with petrol rewinding with existing size of copper winding wire insulating to the existing class of insulation varnishing ovening etc testing at factory under no load assembling transporting to site fixing on foundation re-assembling the motor and testing at load to the satisfaction of engineer-in-charge for motor capacity 100120 hp - note -i transportation and necessary tp for shifting the motor to workshop back is included in the quoted rates ii major spares like coupling bearings etc will be measured and paid under respective item of schedule a, all as per item no 9 above but 5075 hp, all as per item no 9 above but 203040 hp, all as per item no 9 above but 151251075 hp, all as per item no 9 above but 2535 hp, supply only ci impeller suitable of 120 hp capacity centrifugal pump sets, supply only casing ring suitable of 120 hp capacity centrifugal pump sets, supply only impeller ring brass nut suitable of 120 hp capacity centrifugal pump sets, supply only impeller key suitable of 120 hp capacity centrifugal pump sets, supply only coupling key suitable of 120 hp capacity centrifugal pump sets, supply only coupling rubber bushes tyre coupling suitable of 120 hp capacity centrifugal pump sets, supply only shaft sleeve steel suitable of 120 hp capacity centrifugal pump sets, supply only bearing suitable of 120 hp capacity centrifugal pump sets, supply only brass bush suitable of 120 hp capacity centrifugal pump sets, supply only shaft suitable of 120 hp capacity centrifugal pump sets, supply only ms coupling beam jaw gear any type for both pump and motor suitable of 120 hp capacity centrifugal pump sets, supply only gland cap ci suitable of 120 hp capacity centrifugal pump sets, supply only gland bolt and nut suitable of 120 hp capacity centrifugal pump sets, supply only ci impeller suitable of 100 hp capacity centrifugal pump sets, supply only casing ring suitable of 100 hp capacity centrifugal pump sets, supply only impeller ring brass nut suitable of 100 hp capacity centrifugal pump sets, supply only impeller key suitable of 100 hp capacity centrifugal pump sets, supply only coupling key suitable of 100 hp capacity centrifugal pump sets, supply only coupling rubber bushes tyre coupling suitable of 100 hp capacity centrifugal pump sets, supply only shaft sleeve steel suitable of 100 hp capacity centrifugal pump sets, supply only bearing suitable of 100 hp capacity centrifugal pump sets, supply only brass bush suitable of 100 hp capacity centrifugal pump sets, supply only shaft suitable of 100 hp capacity centrifugal pump sets, supply only ms coupling beam jaw gear any type for both pump and motor suitable of 100 hp capacity centrifugal pump sets, supply only gland cap ci suitable of 100 hp capacity centrifugal pump sets, supply only gland bolt and nut suitable of 100 hp capacity centrifugal pump sets, supply only ci impeller suitable of 7550 hp capacity centrifugal pump sets, supply only casing ring suitable of 7550 hp capacity centrifugal pump sets, supply only impeller ring brass nut suitable of 7550 hp capacity centrifugal pump sets, supply only impeller key suitable of 7550 hp capacity centrifugal pump sets, supply only coupling key suitable of 7550 hp capacity centrifugal pump sets, supply only coupling rubber bushes tyre coupling suitable of 7550 hp capacity centrifugal pump sets, supply only shaft sleeve steel suitable of 7550hp capacity centrifugal pump sets, supply only bearing suitable of 7550hp capacity centrifugal pump sets, supply only brass bush suitable of 7550 hp capacity centrifugal pump sets, supply only shaft suitable of 7550 hp capacity centrifugal pump sets, supply only ms coupling beam jaw gear any type for both pump and motor suitable of 7550hp capacity centrifugal pump sets, supply only gland cap ci suitable of 7550 hp capacity centrifugal pump sets, supply only gland bolt and nut suitable of 7550 hp capacity centrifugal pump sets, supply only ci impeller suitable of 3040 hp capacity centrifugal pump sets, supply only casing ring suitable of 3040 hp capacity centrifugal pump sets, supply only impeller ring brass nut suitable of 3040 hp capacity centrifugal pump sets, supply only impeller key suitable of 3040 hp capacity centrifugal pump sets, supply only coupling key suitable of 3040 hp capacity centrifugal pump sets, supply only coupling rubber bushes tyre coupling suitable of 3040 hp capacity centrifugal pump sets, supply only shaft sleeve steel suitable of 3040hp capacity centrifugal pump sets, supply only bearing suitable of 3040hp capacity centrifugal pump sets, supply only brass bush suitable of 3040 hp capacity centrifugal pump sets, supply only shaft suitable of 3040 hp capacity centrifugal pump sets, supply only ms coupling beam jaw gear any type for both pump and motor suitable of 30400hp capacity centrifugal pump sets, supply only gland cap ci suitable of 3040 hp capacity centrifugal pump sets, supply only gland bolt and nut suitable of 3040 hp capacity centrifugal pump sets, supply only ci impeller suitable of 2015125 hp capacity centrifugal pump sets, supply only casing ring suitable of 2015125 hp capacity centrifugal pump sets, supply only impeller ring brass nut suitable of 2015125 hp capacity centrifugal pump sets, supply only impeller key suitable of 2015125 hp capacity centrifugal pump sets, supply only coupling key suitable of 2015125 hp capacity centrifugal pump sets, supply only coupling rubber bushes tyre coupling suitable of 2015125 hp capacity centrifugal pump sets, supply only shaft sleeve steel suitable of 2015125 hp capacity centrifugal pump sets, supply only bearing suitable of 2015125 hp capacity centrifugal pump sets, supply only brass bush suitable of 2015125 hp capacity centrifugal pump sets, supply only shaft suitable of 2015125 hp capacity centrifugal pump sets, supply only ms coupling beam jaw gear any type for both pump and motor suitable of 2015125 hp capacity centrifugal pump sets, supply only gland cap ci suitable of 2015125 hp capacity centrifugal pump sets, supply only gland bolt and nut suitable of 2015125 hp capacity centrifugal pump sets, supply only ci impeller suitable of 755325 hp capacity centrifugal pump sets, supply only casing ring suitable of 755325 hp capacity centrifugal pump sets, supply only impeller ring brass nut suitable of 755325 hp capacity centrifugal pump sets, supply only impeller key suitable of 755325 hp capacity centrifugal pump sets, supply only coupling key suitable of 755325 hp capacity centrifugal pump sets, supply only coupling rubber bushes tyre coupling suitable of 755325hp capacity centrifugal pump sets, supply only shaft sleeve steel suitable of 755325 hp capacity centrifugal pump sets, supply only bearing suitable of 755325 hp capacity centrifugal pump sets, supply only brass bush suitable of 755325 hp capacity centrifugal pump sets, supply only shaft suitable of 755325 hp capacity centrifugal pump sets, supply only ms coupling beam jaw gear any type for both pump and motor suitable of 755325 hp capacity centrifugal pump sets, supply only gland cap ci suitable of 755325 hp capacity centrifugal pump sets, supply only gland bolt and nut suitable of 755325 hp capacity centrifugal pump sets, supply and fix in repairs motor cooling fan of same size as existing suitable for motor of 120100 hp capacity centrifugal pump sets including all fiiting fixtures etc as directed by engr-in-charge, supply and fix in repairs motor cooling fan of same size as existing suitable for motor of 755040 hp capacity centrifugal pump sets including all fiiting fixtures etc as directed by engr-in-charge, supply and fix in repairs motor cooling fan of same size as existing suitable for motor of 302520 hp capacity centrifugal pump sets including all fiiting fixtures etc as directed by engr-in-charge, supply and fix in repairs motor cooling fan of same size as existing suitable for motor of 1512510 hp capacity centrifugal pump sets including all fiiting fixtures etc as directed by engr-in-charge, supply and fix in repairs motor cooling fan of same size as existing suitable for motor of 755 hp capacity centrifugal pump sets including all fiiting fixtures etc as directed by engr-in-charge, supply and fix in repairs motor cooling fan of same size as existing suitable for motor of 32 hp capacity centrifugal pump sets including all fiiting fixtures etc as directed by engr-in-charge, supply and fix in repairs front rear ends bearing of same size as existing suitable for motor of 120100 hp capacity centrifugal pump sets including all fiiting fixtures etc incl taking out motor if not in repair as directed by engr-in-charge, supply and fix in repairs front rear ends bearing of same size as existing suitable for motor of 755040 hp capacity centrifugal pump sets including all fiiting fixtures etc incl taking out motor if not in repair as directed by engr-in-charge, supply and fix in repairs front rear ends bearing of same size as existing suitable for motor of 302520 hp capacity centrifugal pump sets including all fiiting fixtures etc incl taking out motor if not in repair as directed by engr-in-charge, supply and fix in repairs front rear ends bearing of same size as existing suitable for motor of 1512510 hp capacity centrifugal pump sets including all fiiting fixtures etc incl taking out motor if not in repair as directed by engr-in-charge, supply and fix in repairs front rear ends bearing of same size as existing suitable for motor of 755 hp capacity centrifugal pump sets including all fiiting fixtures etc incl taking out motor if not in repair as directed by engr-in-charge, supply and fix in repairs front rear ends bearing of same size as existing suitable for motor of 32 hp capacity centrifugal pump sets including all fiiting fixtures etc incl taking out motor if not in repair as directed by engr-in-charge, supply laying and fixing or passing through pipes ducts or laid under floor of through walls etc jointing and testing lt xlpe insulated pvc sheathed electric cable 1100 volt grade heavy duty isi marked with copper conductor and over all served with an outer sheath of pvc from panel to motor including providing copper lugs as per site requirement including taking down old cable complete size of cable 70 sqmm single core as specified and directed by engineer-in-charge note- cost of dwc pipe of suitable size for laying of xlpe copper cable from panel to motor for sizes up to 70 sqmm shall deemed to be included in the quoted rate, all as per item 104 above but size of cable 35 sqmm single core, all as per item 104 above but size of cable 25 sqmm single core, all as per item 104 above but size of cable 16 sqmm single core, taking out the submersible pump set of 10755 hp capacity from deep bore well with connected cable and column pipes of 3m length with flange end 32 dia appx 10 nos per bore well and disconnecting the cable for removing the submersible pump set for carrying out necessary repairs all as directed by engineer-in-charge, lowering of submersible pump set 10755 hp in bore well with connected cable column pipes re-assembling column pipe of 3m long with flange ends 32 dia appx 10 nos and testing and commissioning of pump set after repairs including rectification of any leakage to the entire satisfaction of engineer-in-charge, repairs to submersible pumping set 10755 hp by dismantling pumps and motor carrying out required repairs to pump by machines ie grindingpolishing reassembling after renewal of all worn out spare parts cleaning and refixing with motors with required coupling etc complete testing all as specified directed by engineer-in-charge note - i rewinding of motor renewal of parts will be measued paid separately ii rate of taking down of old unserviceable spare parts shall be included in quoted rate of this item, rewinding of ac 3 phase induction motor of 10 hp capacity submersible pump motor by cutting of burnt out winding cleaning of starter slots cleaning bleaching of motor and rewinding with appropriate gauge of pvc insulated copper winding wire complete including all required parts complete all as specified directed by engineer-in-charge, rewinding of ac 3 phase induction motor of 755 hp capacity submersible pump motor by cutting of burnt out winding cleaning of starter slots cleaning bleaching of motor and rewinding with appropriate gauge of pvc insulated copper winding wire complete including all required parts complete all as specified directed by engineer-in-charge, taking out the submersible pump set of 50 hp capacity from rainwater sump at cair with connected cable and column pipes of 3m length with flange end 32 dia and disconnecting the cable for removing the submersible pump set for carrying out necessary repairs all as directed by engineer-in-charge, repairs to submersible pumping set 50 hp by dismantling pumps and motor carrying out required repairs to pump by machines ie grindingpolishing reassembling after renewal of all worn out spare parts cleaning and refixing with motors with required coupling etc complete testing all as specified directed by engineer-in-charge note - i rewinding of motor will be measued paid separately ii rate of renewalrepairs of unserviceable parts of motor and pump set are deemed to be included in the quoted rate and incl taking down of old unserviceable spare parts shall be included in quoted rate, rewinding of ac 3 phase induction motor of 50 hp capacity submersible pump motor by cutting of burnt out winding cleaning of starter slots cleaning bleaching of motor and rewinding with appropriate gauge of pvc insulated copper winding wire complete including all required parts complete all as specified directed by engineer-in-charge, supply only for fixing thrust bearing plate for motor of submersible pump set suitable for 10755 hp motor, supply only for fixing assembly for coupling sleeve for motor of submersible pump set suitable for 10755 hp motor, supply only for fixing winding protector set for motor of submersible pump set suitable for 10755 hp motor, supply only for fixing motor bearing bush for motor of submersible pump set suitable for 10755 hp motor, supply only for fixing drain plug for motor of submersible pump set suitable for 10755 hp motor, supply only for fixing sand guard for motor of submersible pump set suitable for 10755 hp motor, supply only for fixing key for thrust plate for motor of submersible pump set suitable for 10755 hp motor, supply only for fixing impeller of submersible pump set suitable for 10755 hp pump, supply only for fixing stage bowl of submersible pump set suitable for 10755 hp pump, supply only for fixing bowl fixing steel bolt and nut with washer of submersible pump set suitable for 10755 hp pump, supply only for fixing bearing sleeve of submersible pump set suitable for 10755 hp pump, supply only for fixing shaft nut with washers of submersible pump set suitable for 10755 hp pump, supply only for fixing suitable bearing bush of submersible pump set suitable for 10755 hp pump, supply only for fixing suitable neck ring of submersible pump set suitable for 10755 hp pump, supply only for fixing casing wear ring of submersible pump set suitable for 10755 hp pump, supply only for fixing suitable strainer of submersible pump set suitable for 10755 hp pump, supply only for fixing suitable shaft seal of submersible pump set suitable for 10755 hp pump, supply only for fixing stage gasket of submersible pump set suitable for 10755 hp pump, m l for lifting the submersible non clog type pumpset of 151075 hp capacity from sewage well disconnecting the cable transporting the pumpset to workshop dismantling the motor megger testing the motor removing the burnt damaged winding rewinding with appropriate size of copper winding wires re-insulation with appropriate class of insulation to the existing class varnishing and bakeing replacing the wornout bearing bushing assembling testing of motor opening the pump set cleaning the impellers supplying and fixing required nos of bearing bush after removing existing worn out bush bearing of pump set upto 08 stages assembling the pump re-assembling the motor pump shifting to site connecting the cable and lowering the pump set along with gi pipes cables including testing complete all as directed note major spares like impeller etc will be measured paid separately, s f in repair contactor 3 phase ac 440 volt of 25 amps capacity complete all as specified directed by engineer-in-charge, s f in repair contactor 3 phase ac 440 volt of 32 amps capacity complete all as specified directed by engineer-in-charge, s f in repair contactor 3 phase ac 440 volt of 40 amps capacity complete all as specified directed by engineer-in-charge, s f in repair contactor 3 phase ac 440 volt of 70 amps capacity complete all as specified directed by engineer-in-charge, s f in repair contactor 3 phase ac 440 volt of 95 amps capacity complete all as specified directed by engineer-in-charge, s f in repair contactor 3 phase ac 440 volt of 115 amps capacity complete all as specified directed by engineer-in-charge, repairreplacement of following us itemsparts of lt panel board if required with necessary copper wiring lugs etc complete to make item functional all as specified and directed by engineer-in-charge- a digital voltmeter 0-500 v, all as per item 141 above but b digital ammeter 0-200 a, all as per item 141 above but c ammeter ct type 0-300 a, all as per item 141 above but d selector switch as per existing, all as per item 141 above but e phase indicator r y b as per existing, all as per item 141 above but f electronic relay of any required size, all as per item 141 above but g aluminium busbar as per existing, all as per item 141 above but h cable lugs as per existing, sf on load change over switch four pole 400a 415 volts ac manual changeover open execution type with handle including taking down old change over switch connection complete all as directed, m l for disconnecting the electrical connections from the panel to the sewage motor 30 hp dis-connecting the pump motor and shifting the same to the upper platform from the sewage well carefully using necessary t p and dismantling the rusted structural steel base plate from the foundation bed fabricating new base plate using structural steel sections of the same shape size of the existing base plate applying two coats of synthetic enamel black paint over a coat of red oxide fixing complete on the exisitng foundation bed using new foundation bolts as required at site lowering of the pump motor fixing on the base plate with proper shaft allignment and connecting with coupling connecting the electrical water connections checking for smooth running of the pump complete all as directed note - 1 steel sections and coupling shall be measured and paid seperatly under respective items of this schedule 2 the quoted rates are inclusive of necessary t p painting nuts bolts washers etc, repairs to sewage motor 30 hp by dismantling pumps and motor carrying out required repairs to pump by machines ie grindingpolishing reassembling after renewal of all worn out spare parts cleaning and refixing with motors with required coupling etc complete testing all as specified directed by engineer-in-charge note - i rewinding of motor renewal of parts shall be measued paid separately ii rate of taking down of old unserviceable spare parts shall be included in quoted rate of this item, taking out angle iron and m l for rolled mild steel in joists channel angle or tee sections as in main and cross beams of fe 410-w grade steel for ladders for ug sumps oh tanks including cutting welding grinding sharp corners etc all as directed note - the quoted rates are inclusive of unloading fabrication work at site reducing to required shape size hoisting fixing etc including prepration of new untreated surfaces and painting of with one coat of red oxide primer and two coats of black paint all as required at site including taking down the old unsv ones complete all as directed, dismantling of existing panel board of any type with all accessoires complete design supply installation testing and commissioning of factory-built indoor double door lt panel cubicle type floor mounted compartmentalised fabricated from crca sheet steel with minimum 20 mm thick doorsfront coversload-bearing members and 16 mm internal partitionsgland plates the enclosure shall be phosphated by seven-tank pretreatment and finished with epoxy polyester powder coating of minimum 80 microns shade ral 7035 suitable for indoor use enclosure shall be suitable for ac supply system 415 volts 3 phase 4 wire 50 hz degree of protection shall be ip-54 cable entry from bottom side in separate cable alley on both sides separated with bakelite sheet of suitable size including internal wiring with pvc insulated stranded copper wire 1100 volts grade panel shall conform to isiec 61439-1 61439-2 and be routinetype tested the panel shall consist of electrolytic grade tpn aluminium bus bars with rated at minimum 15 times the main incoming switchgear rating provided with colour coded heat shrinkable sleeves the panel shall be provided with separate compartments for each switchgear including instrumentation such as ammeters voltmeter phase indicating lamps etc with double-stud hinged door front rear openable with locking arrangement including interlocking with switchgears the panel shall be fixed on angle iron frame made of angles 50 x 50 x 6 mm embedded 200 mm below ground level in pcc 124 type b-1 using 20 mm grade stone aggregate 600 mm above ground level the panel is designed for 02 nos centrifugal pump motors of 100 hp 746 kw rating full load current 136 a each with electronic soft starters with integral bypass contactor and comprehensive motor protection comprising the following, dismantling of existing panel board of any type with all accessoires complete design supply installation testing and commissioning of factory-built indoor double door lt panel cubicle type floor mounted compartmentalised fabricated from crca sheet steel with minimum 20 mm thick doorsfront coversload-bearing members and 16 mm internal partitionsgland plates the enclosure shall be phosphated by seven-tank pretreatment and finished with epoxy polyester powder coating of minimum 80 microns shade ral 7035 suitable for indoor use degree of protection ip-54 enclosure shall be suitable for ac supply system 415 volts 3 phase 4 wire 50 hz cable entry from bottom side in separate cable alley on both sides separated with bakelite sheet of suitable size including internal wiring with pvc insulated stranded copper wire 1100 volts grade panel shall conform to isiec 61439-1 61439-2 and be routinetype tested the panel shall consist of electrolytic grade tpn aluminium bus bars with rated at minimum 15 times the main incoming switchgear rating provided with colour coded heat shrinkable sleeves the panel shall be provided with separate compartments for each switchgear including instrumentation such as ammeters voltmeter phase indicating lamps etc with double-stud hinged door front rear openable with locking arrangement including interlocking with switchgears the panel shall be fixed on angle iron frame made of angles 50 x 50 x 6 mm embedded 200 mm below ground level in pcc 124 type b-1 using 20 mm grade stone aggregate 600 mm above ground level the panel is designed for 02 nos centrifugal pump motors of 120 hp 895 kw rating full load current 163 a each with electronic soft starters with integral bypass contactor and comprehensive motor protection comprising the following, taking down of existing old and unservicebale flow meter of any design and type design supply installation testing and commissioning of electromagnetic flowmeter dn250 with remote external flow display ip65ip67 protection suitable for outdoor installation complete with instrumentation signal cabling suitable for continuous flow measurement on 250 mm dia potablerawtreated water pumping main with flow indication displayed remotely inside pump house the item comprises the following a programmable remote external digital flow display unit suitable for receiving 4-20 ma hart signal from the electromagnetic flow meter and displaying instantaneous flow rate cumulative flow cumhr cumday and mld inside pump house complete with minimum 4-digit ledlcd display programmable engineering units isolated analogue input configurable scaling totaliser function minimum 2 alarm relays accuracy better than 01 230 v ac auxiliary supply ip54 enclosure wallpanel mounting arrangement surge protection and all mounting hardware wiring terminals and accessories required for satisfactory operation 01 no make siemens sitrans rd100 cat no 7ml5741-1ab00-0ad0 schneider electric harmony indicator cat no xbtgt2220 autonics mt4w-dv-41 b i measuring principle faradays law of electromagnetic induction full bore bidirectional flow measurement virtually independent of pressure density temperature and viscosity of the medium ii nominal diameter dn250 10 suitable for 250 mm dia water pipeline iii measuring range device family 05 mh to 263 000 mh 25 galmin to 1665 mgald scaled to line size and application iv accuracy 05 of reading 1 mms 004 ins standard measurement error v max process pressure rating pn40 class 300 20k, ml for design fabrication supply transportation erection testing and commissioning of premium outdoor weatherproof illuminated main entrance sign board comprising 3 mm thick exterior grade pvdf coated fire-retardant acp fascia panel aludecor viva eurobond alstone or equivalent with cncrouter cut openings for letters logos and insignia edge folding and finishing complete fabricated ms internal structural framework of 40402 mm min shs complete with cutting welding grinding one coat zinc chromate primer and two coats synthetic enamel paint finish designed to withstand wind and dead loads 3d raised illuminated acrylic letters numerals bilingual text insignia and logo made from 8 mm thick imported cast acrylic face sun acryl jindal equivalent approved lasercnc cut uv resistant with 3 mm acrylicaluminium returns 50100 mm depth as approved and 5 mm pvcacrylic backing letters fixed with concealed ss stud fixing system complete with high brightness ip65ip66 waterproof led modules samsung philips osram operating on 12v dc through weatherproof constant voltage smps driver meanwell philips inventronics hilux with surge overload and short circuit protection minimum 50 000 hr led life cool white 6500k or as approved including complete internal frls copper wiring ferrules connectors ip65 junction boxes and accessories providing and fixing ss-304 grade decorative outer boundary frameborder fabricated from minimum 12 mm thick ss sheetbox section jindal tata ss or equivalent mirror or hairline satin finish seamlessly welded polished and decoratively buffed at corners providing and fixing ss-304 grade support polesmounting structure of minimum 150 mm dia with coating of red oxide and two coats of black paint with 10 mm thick ss base platesheight may vary from 2m to 6m ss-304 anchor bolts chemical anchoring clamps gussets and bracing capable of withstanding wind load up to 180 kmph and full dead load of sign board including frls 15 sqmm copper wiring in uv resistant pvcflexible conduit 6a sp mcb isolator weatherproof silicone sealing scaffolding hoisting welding drilling alignment testing commissioning cleaning and handing over, m l for laying connecting testing three core 6 sqmm copper conductor flexible pvc insulated pvc sheathed heavy duty flat cable 1100 volts grade for centrifugalsewage non clog pumps from panel to motor duly clamped on walls run through conduits etc including taking out unserviceable cable all as speciifed and as directed, material and labour for scraping the peeled off paint of pumping set up to 120 hp capacity along with base foundation plate applying metal paste on uneven surfaces to make the surface smooth and applying a coat of synthetic enamel paint of existing shade and writing the mes sm number on the motor pump set all as directed, material and labour for scraping the peeled off paint of suction delivery water lines ms duct covers control valves at pumping installations upto 6 mtr from pump outlet and 3 mtr from pump outlet applying metal paste on uneven surfaces as necessary to make the surface smooth and applying a coat of synthetic enamel paint of existing shade and sign writing all as directed, supply fix in repairs mccb 400 amps 35 ka 4 pole adj thermal and adj magnetic release trip unit 415 volt ac 50 hz ics-100icu including connecting up incoming out going cables with suitable lugs and testing complete all as specfied and as directed, supply fix in repairs mccb 250 amps 25 ka 4 pole adj thermal and adj magnetic release trip unit 415 volt ac 50 hz ics-100icu including connecting up incoming out going cables with suitable lugs and testing complete all as specfied and as directed, supply fix in repairs mccb 200 amps 25 ka 4 pole adj thermal and adj magnetic release trip unit 415 volt ac 50 hz ics-100icu including connecting up incoming out going cables with suitable lugs and testing complete all as specfied and as directed, supply fix in repairs mccb 100 amps 25 ka 4 pole adj thermal and adj magnetic release trip unit 415 volt ac 50 hz ics-100icu including connecting up incoming out going cables with suitable lugs and testing complete all as specfied and as directed, supply and fix in repairs mccb 4 pole 415 volts 125 amps 25 ka 50 hz ac adj thermal and adj magnetic release trip unit ics-100icu including connecting up incoming out going cables with suitable lugs and testing complete all as specified and as directed, earthing complete with galvanised steel earth plate electrode 60cm x 60cmx 60mm thick burried directly in ground vertically earth pit not less than 225m deep below ground level with top edge of the earth plate not less than 15m deep below normal ground level connected to galvanised iron strip 32x6 mm 75m length by means nuts check nuts and washers of gi or steel connected to main switch board including watering arrangement with pcc chamber ms wire gauge ci cover with frame incl excavation in any strata and returning filling removal surplus soil charcoal salt complete all as shown in electric plate no 3 of ssr part i earth test point shall be provided at suitable point, ml for cleaning of ug sewage sump by draining out water removing the silt mud and any other foreign materials from bottom of well of capacity up to 60 lakh ltrs using vehicle kambi 6 lcn mounted with compressor and sucker tank of ms kam-avida enviro engineers pvt ltd pune or similar model vehicle washing down with water for smooth functioning of sewage pipe lines disfection with bleaching powder etc applying one coat of white wash for the entire surfaces complete all as specified and as directed note the receipt of payment made towards the vehicle charges for removing of sludge shall be attached with the completion report submission without original receipt payment will not be done to the contractor, chemical and bacteriogical analysis of water as per is-10500 sample collected from bore wellsshallow wellsbwssb water user point all as directed by engr-in-charge note - water to be tested once in 1 months and approved at nabl lab note the receipt of payment made towards the water analysis charges to nabl lab shall be attached with the report submission without original receipt payment will not be made to the contractor
AI summaryBid / No Bid DecisionGenerate annexuresDraft Full Bid
m l for disconnecting all electric and water supply connections and other related items and lifting the unserviceable centrifugalmono block pump of capacity 4050hp 3 phase 415 v by mechanicalmanual method including dismantling the water supply lines and keeping the same in safe custody for repair including transportation of the defective pump set and motor from pump house to workshop for repair and back and re-installation the same on exisisting position after necessary repair including testing on completion all as directed by the engr-in-charge, m l for disconnecting all electric and water supply connections and other related items and lifting the unserviceable centrifugalmono block pump of capacity 20-30 hp 3 phase 415 v by mechanicalmanual method including dismantling the water supply lines and keeping the same in safe custody for repair including transportation of the defective pump set and motor from pump house to workshop for repair and back and re-installation the same on exisisting position after necessary repair including testing on completion all as directed by the engr-in-charge, m l for disconnecting all electric and water supply connections and other related items and lifting the unserviceable centrifugalmono block pump of capacity 75 to 15 hp 3 phase 415 v by mechanicalmanual method including dismantling the water supply lines and keeping the same in safe custody for repair including transportation of the defective pump set and motor from pump house to workshop for repair and back and re-installation the same on exisisting position after necessary repair including testing on completion all as directed by the engr-in-charge, m l for disconnecting all electric and water supply connections and other related items and lifting the unserviceable centrifugalmono block pump of capacity 5 hp 3 phase 415 v by mechanicalmanual method including dismantling the water supply lines and keeping the same in safe custody for repair including transportation of the defective pump set and motor from pump house to workshop for repair and back and re-installation the same on exisisting position after necessary repair including testing on completion all as directed by the engr-in-charge, m l for disconnecting all electric and water supply connections and other related items and lifting the unserviceable centrifugalmono block pump of capacity 2 to 3 hp capacity 3 phase 415 v by mechanicalmanual method including dismantling the water supply lines and keeping the same in safe custody for repair including transportation of the defective pump set and motor from pump house to workshop for repair and back and re-installation the same on exisisting position after necessary repair including testing on completion all as directed by the engr-in-charge, m l for dismantling the unserviceable parts and burnt out copper winding from pump - motor of capacity 30 to 50 hp 3 phase 415v and rewinding the motor with supper enamelled copper wire of suitable gauge including heating varnishing replacement of defective spare parts re-assembling and painting the motor with two coats of supper enamelled paint and carrying out necessary tests in presence at site as directed note- a spare parts copper winding wire will be measured paid seperately as all as per supply only 2 labour charge for fixing parts shall deemed to be included in the unit rate, m l for dismantling the unserviceable parts and burnt out copper winding from pump - motor of capacity 75 to 20 hp 3 phase 415v and rewinding the motor with supper enamelled copper wire of suitable gauge including heating varnishing replacement of defective spare parts re-assembling and painting the motor with two coats of supper enamelled paint and carrying out necessary tests in presence at site as directed note- a spare parts copper winding wire will be measured paid seperately as all as per supply only 2 labour charge for fixing parts shall deemed to be included in the unit rate, m l for dismantling the unserviceable parts and burnt out copper winding from pump - motor of capacity 2 to 50 hp 3 phase 415v and rewinding the motor with supper enamelled copper wire of suitable gauge including heating varnishing replacement of defective spare parts re-assembling and painting the motor with two coats of supper enamelled paint and carrying out necessary tests in presence at site as directed note- a spare parts copper winding wire will be measured paid seperately as all as per supply only 2 labour charge for fixing parts shall deemed to be included in the unit rate, supply only copper winding wire with supper enamelled copper wire of suitable gauge as per capacityrating of motor complete all as specified and directed by engr - in - charge, taking down the unserviceable parts from the centrifugal pump of capacity 30-50 hp three phase 415 v including over hauling servicingcleaning throughly discharge suction cases impellers shaft and re-assembling pump carefully including servicing cleaning and painting the parts with two coats water proofing supper enamelled paint after preperation of surfaces manualy including repairreplacement of unservicable parts as required at site etc and re-assemblingre-installing the pump complete all as specified and directed note- a spare parts shall be measured paid seperately as supply only items b labour charge for fixing parts shall deemed to be included in the unit rate, taking down the unserviceable parts from the centrifugal pump of capacity 75 to 20 hp three phase 415 v including over hauling servicingcleaning throughly discharge suction cases impellers shaft and re-assembling pump carefully including servicing cleaning and painting the parts with two coats water proofing supper enamelled paint after preperation of surfaces manualy including repairreplacement of unservicable parts as required at site etc and re-assemblingre-installing the pump complete all as specified and directed note- a spare parts shall be measured paid seperately as supply only items b labour charge for fixing parts shall deemed to be included in the unit rate, taking down the unserviceable parts from the centrifugal pump of capacity 2 to 50 hp three phase 415 v including over hauling servicingcleaning throughly discharge suction cases impellers shaft and re-assembling pump carefully including servicing cleaning and painting the parts with two coats water proofing supper enamelled paint after preperation of surfaces manualy including repairreplacement of unservicable parts as required at site etc and re-assemblingre-installing the pump complete all as specified and directed note- a spare parts shall be measured paid seperately as supply only items b labour charge for fixing parts shall deemed to be included in the unit rate, m l for machine work to the worn out portion of non clog submersible pump shaft of capacity including metalling cutting polishing and checking the accuracy on the lath machine complete all as directed by engr-in-charge, supply only ball bearing for motor all as per existing and specified and directed by engr-in-charge, supply only mechanical seal for for pump - motor all as per existing ans specified and directed by engr-in-charge, supply only impeller as per existing all as per specified and directed by engr-in-charge, supply only impeller key as per existing all as per specified and directed by engr-in-charge, m l for machine work to the worn out portion of non clog submersible pump shaft of capacity including metalling cutting polishing and checking the accuracy on the lath machine complete all as directed by engr-in-charge, supply only ball bearing for motor all as per existing and specified and directed by engr-in-charge, supply only mechanical seal for for pump - motor all as per existing ans specified and directed by engr-in-charge, supply only impeller as per existing all as per specified and directed by engr-in-charge, supply only impeller key as per existing all as per specified and directed by engr-in-charge, m l for machine work to the worn out portion of non clog submersible pump shaft of capacity including metalling cutting polishing and checking the accuracy on the lath machine complete all as directed by engr-in-charge, supply only ball bearing for motor all as per existing and specified and directed by engr-in-charge, supply only mechanical seal for for pump - motor all as per existing ans specified and directed by engr-in-charge, supply only impeller as per existing all as per specified and directed by engr-in-charge, supply only impeller key as per existing all as per specified and directed by engr-in-charge, m l taking out vertical submersible pump motor set from existing borewellof capacity from 20 hp to 75 hp capacity dismantling pump complete after disconnecting all electrical connections and repairoverhauling including replacement of following worn out parts as per sample note i spares required for replacement shall be measured and paid as supply only under respective items ii reassembling lowering in sewage sump to its original place testing and transport will be included in quoted rate, supply only gun metal bush of capacity complete all as specified directed, supply only impeller complete all as specified and directed, supply only impeller key complete all as specified and directed, supply only neck ring bronze complete all as specified and directed, supply only guide ring complete all as specified and directed, supply only lock bolt for impeller complete all as specified and directed, supply only shaft sleeve complete all as specified and directed, supply only shaft coupling screwed complete all as specified and directed, supply only coupling pin bush complete all as specified and directed, supply only ball bearing complete all as specified and directed, supply only lock bolt for shaft coupling complete all as specified and directed, all as per item no 1501 but top shaft complete all as specified and directed, supply and fix in repair dol starter along with single phase preventor in sheet steel enclosure 3 phase 415 volts with contactor suitable for 1 to 6 hp electric motor complete all as specified and directed make lt mk1 dol bchhavells, supply and fix in repair dol starter suitable of pumps of capacity upto 10hp heavy duty complete including replacement of existing starter complete make la mk1 dol bchhavells, supply and fix in repair fully automatic fasd star delta starter along with single phase preventor in powder coated enclosure with pu gasket suitable 5 hp to 10 hp including all electric connection with ammeter and volt meter onoff trip indicator including protection against phase failure phase imbalance phase reversal complete all as specified and directed make lt mk1 fasdbch havells, m l for repairservicing of existing sluice valve of 100 mm after dismantling of upper cover remove the spindle and make it leak proof by replace the gland packing nut bolt with washer and gasket of both side all as per specified and directed by engr-in-charge, m l for repairservicing of existing sluice valve of 150 mm after dismantling of upper cover remove the spindle and make it leak proof by replace the gland packing nut bolt with washer and gasket of both side all as per specified and directed by engr-in-charge, s f in replacement voltmeter digital type complete all as specified and directed by engineer - in - charge, s f in replacement ammeter digital type of capacity up to 100 amp complete all as specified and directed by engineer - in - charge, supply and fix in repairs on-off push button pendants with elements red green orange complete all as specified and as directed by engr-in-charge, supply fixing mcb single pole and neutral spn of capacity 63 amps 240 volts breaking capacity 10 ka c series fixed in proper position all as directed by the engineer-in-charge make legrand or equivalent, supply fixing mcb single pole sp of capacity 6 amps to 32 amps 240 volts ac breaking capacity 10 ka c series fixed in proper position all as directed by the engineer-in-charge make legrand or equivalent siemensabb, material and labour for development of tube well by at the site including dismatling existing gicpvchdpe bore well pipes up to 120 mtrs depth including taking up submersible pumps and flushing of bore well with air compressor of capacity 250psi1000 cum and related accessories at least 10 hours till water discharge is free from sand and potable water and to achieve maximum discharge capacity including necessary development complete and lowering submersible pump with gicpvchdpe borewell pipes complete including testing of borewell all as specified and directed note i unit rate quoted under this items shall deemed to be inclusive of transportation of tools and equipments as required to the site of work and removing the same after completion of work ii verticality test of the tube well structure shall be carried out and the cost of the same shall be deemed to be included in unit quoted rate, excavation in trenches not exceeding 15 metre wide and not exc 15 metre in depth for foundation of pole stay or cable trenches and getting out in soft disintegrated rock complete all as specified and as directed by the engineer in charge, returning filling in incl spreading leveling watering and well ramming in layers not exceeding 25 cm in soft loose soil complete all as specified and as directed by the engineer in charge, removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 15 metre above the starting point all as specified and as directed by the engineer in- charge, sf cpvc ball valve of size 20 mm dia suitable for cpvc pipe incl necessary fittings and taking down old one complete all specified and directed make supremeeurotech astralsfmc, supply and fix in trenches high pressure cpvc pipes sdr-135 plain cpvc sdr 11 fittings including all necessay fittings solvents of size 40 mm dia complete including taking down old one all as specified and directed make supremeeurotech astralsfmc, supply and fix in trenches high pressure cpvc pipes sdr-135 plain cpvc sdr 11 fittings including all necessay fittings solvents of size 20 mm dia complete including taking down old one all as specified and directed make supremeeurotech astralsfmc, m l for replacement of foot valve 4050 mm dia pipe complete including taking tp suction lines from up sump of depth max up to 50 mtrs and lowering after replacemnt of foot valve complete all as specified, m l for replacement of foot valve 80 mm dia pipe complete including taking tp suction lines from up sump of depth max up to 50 mtrs and lowering after replacemnt of foot valve complete all as specified, m l for road cutting hard standing for width not less than 30 cm and not exceeding depth up to 45 cm for laying of pipe lines and making good to road hard standing area with necessary cement concrete complete all as directed, sump of capacity 1 00 000 gln at main pump house and g13, sump of capacity 50 000 gln at main pump house offs md accn area swimming pool, sump of capacity 40 000 gln ward room mess, sump of capacity 25 000 gln at dsc civ md accn, oht of capacity 50 000 gln at family qtr oht, oht of capacity 75 000 to 1 00 000 gln at eklavya, oht of capacity 5000 gln at near mi room auditoriummysure block, sump of capacity 1 75 000 gln at new nwc, ml for cross arm bracings support clamps and back plates fabricated from structural steel section including nuts bolts washer welding drilling hole for bolts bending in any shape or size as indicated or directed and inclusive of one coat of aluminium primer one under coat and one finishing coat of aluminium paint for for repair repalcement of portion of existing ladder at oht as per existing specification frame cover for valve chamber etc complete all as specified and as directed, m l for dismantling cross-arms of ms channel or angle sections etc complete and setting aside for re-use with in 50m, ml for earthing complete with galvanised steel earth plate electrode 600 x 600 x 60 mm thick burried directly in gorund earth pit not less than 225 mtr normal ground level and top edge of earth plate not less than 15 mtr below normal ground level using galvanised iron strip 254mm as earthing lead with bolts nuts check nuts and washers of galvanised iron protection pipe light grade of 40 mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt watering funnel with wire mesh earth pit chamber and cover ci frame pcc 136 type c-2 all as shown in electrical plate no-3 of ssr part-i of 2009 connected to earthing test point all as specified and indicated including all earth work excavation returning filling and disposal of surplus soil and testing on completion, supply fix and testing smart digital 10-levels indicator stage type with mechanism to detect display the water level in an underground overhead tank fixed on wall oht with necessary pvc corrosion free enclosure corrosion maintenance free magnetic sensors buzzer alarm sounds on low high levels including necessary fittings on sensing the water level from oht of height up to 21 mtrs ug sump of depth at 60 mtrs complete make sinetrac, m l for testing of water samples from sourceinside the ins mandovi from ohtsumpbore wellsany service tanks and testing in govt lab govt approved pvt labs for bacterial and chemical testing of water sample to find out the total coliforms e coli faecal coliforms ph nitrates nitrates and turbidity complete including taking the samples in every qe as and when required as directed by engineer in charge note the m l for collection of samples including new container as per lab standards transportaion cost up to lab is included in unit rate, supply fabricating installation in replacement self illumnated acrylic led sig board factory made with fixed on wall iron frame as directed letter length 30 cm max up to 40 cm letter thickness 5 cm max up to 6 cm customized design of letters back-lit signage including embedding the signage baord firmly with the wall ms angle frameas per approved art work and nomenclature as given below - note nomenclature of sign board include letterslogos etc complete as directed box with frame - 25 x 25 mm square pipe 18 g frame with cross supports spacing not exceeding 10 m on the box length including 20 mm x 20 mm ms square pipe 18 g stifferenrs duly white enamel painted in 2 coats over a coat of zinc oxide iron primer depth of box should not be less than 165 mm side top back and bottom panels - made out of 24 gauge chemically treated gi sheets duly precoated powder coated with white matt finish coating on both inner and outer surface top panel to have 24 guage precoated drip cap fixed with pop rivet or machine moulded to shape of 25 mm on front and side to prevent damages due to rain etc the bottom panel should be provided with access door fixed with ss screws and suitable housing for led drivers led module - led 12v module beam angle 150 degrees with ip rating 64 072 w70 lumens per module of 3 leds with 7000 to 8000 k colour temperature make tridonic osram cree ge led configuration - 29 led modules per sq mt equal division on spacing based on height of box and one module every 020 m on running length of box led power supply - input 230 v ac power supply should be cpcc constant power constant current of 30w60w120 w each graphics - graphics shall be computer plotter cut with translucent cast vinyl matching the colour specification of the installation, m l for servicing of filtration plant at water supply installations including removing the existing gravels in sand filter complete painting of filtration plant including replacing unserviceble nuts bolts of cover plate complete note work shall be done through the reputed firm sandgravepubbles required for replacement is measured and paid seperately under respective items, supply and fill in replacement pabbles size 1 15 mm in sand filter including getting out from the filter all as per specified and directed by engr-in-charge, supply and fill in replacement pabbles size 1 - 34 mm in sand filter including getting out from the filter all as per specified and directed by engr-in-charge, supply and fill in replacement pabbles size 34 12 mm in sand filter including getting out from the filter all as per specified and directed by engr-in-charge, supply and fill in replacement corese siliex size 12 14 mm in sand filter including getting out from the filter all as per specified and directed by engr-in-charge, supply and fill in replacement corese siliex size 14 110 mm in sand filter including getting out from the filter all as per specified and directed by engr-in-charge, supply and fill in replacement graded sand in sand filter including getting out from the filter all as per specified and directed by engr-in-charge, m l for surface excavation at water supply installations not exceeding 30 cm deep and averaging 15 cm deep and getting out soft loose soil removing shrubs small trees height up to 10 mtrs removing the grass from route as directed note i rate includes removing all waste material and grass not excceding 250 mtrs distance from installation depositing where directed at a level not exceeding 15 mtrs above the starting point and cleaning of yard complete all as specified and directed by eicii repeated cleaning in each installation shall be measured and paid seperately with time interval of minimum 2 months, m l for laying of weed control mat sorrounding area of over head tank ug sump insid ethe water supply installations of size thickness less than 100 gsm ans size 1012 x 100 mtrs of roll laid in level surface with 7 inch 18 cm high quality pvc nails for firm hold for weed mat at earth surfaces in regular intervals in between 5 mtrs complete alla s specified and as directed, supply and fix fire retardant insulated synthetic mat for lt 1100 volt of 20 mm thick - 10 conforming to is tested for breakdown strength ageing properties insulation resistance effect of acid alkaline diesel transformer oil leakage current test fire test etc having the width of 1000mm -20mm complete as required sutable and using adhasive and alied chemical and scaling of all part s of all joints and border ends and fixing tape making good as paste near lt panel boards complete all as specified and as directed make vardhamanjyothicease fireqquivalent, s f junction box made from smcfrp sheet ready made of size300x 200x105 mm with aluminium bus bar of 100 amp capacity for ryb and half for neutral made in suitable size fixed inside the junction box with necessary supporting insulators fixed on hylem sheet ms sheet steel fixed inside the bottom portion of box to connect the cable gland complete entire assembly fixed to pole wall with ms clamp 25 x 5 mm and nuts bolts or inside the copping of pole post top including mcb sp 6 amp 10 ka 240 v - 1 no with necessary size copper lugs for connecting cables from junction box to fittings complete all as directed by engineer-in-charge make sintex right hingedhensal, s f lt feeder piller box 20 mm thick oin door type cpri approved with 100 amp copper bus bar for ryb and neutral with necessary control wiring consisting of following - incomming mccb 100 amp 4 pole 16 ka - 01 nos multi function meter for v-a-f -01 nos indicating lamp for ryb - 01 set out going mcb tpn - 32 amp - 02 nos mpcb 20 - 25 amp with ol sc and single phase preventer - tpn 32 amp 10 ka - 02 nos fully automatic starter for 10 hp pump motor - 02 nos curent transformer 20 25- 5amp - 06 nos push buttonfor startstop - 04 nos led indicating lamp onoff trip - 06 nos mcb 6 amp - 02 nos note i panel shall be floor mounted inside the pump house ii minor variation in range of starter mpcb ct shall be selected as pe the make approved, supply and fix in replacement hdpe pipe of pressure rating 6 kgf sq cm of size 50 mm inner dia in bore well including all necessay fittings like elbow tee socket reducer bushings step over bends end caps end plugs etcand with including taking up old unserviceble gi pipes pipes complete all as specified and directed by engineer in charge make supremeeurotech astralsfmc, sf pvc insulated pvc sheathed stranded copper conductor as in flat submersible water proof cable of size 16 sqmm 3 core 1100 volts grade incl taking down old one complete as specified and directed, sf pvc insulated pvc sheathed stranded copper conductor as in flat submersible water proof cable of size 10 sqmm 3 core 1100 volts grade incl taking down old one complete as specified and directed, sf pvc insulated pvc sheathed stranded copper conductor as in flat submersible water proof cable of size 6 sqmm 3 core 1100 volts grade incl taking down old one complete as specified and directed, sf pvc insulated pvc sheathed stranded copper conductor as in flat submersible water proof cable of size 4 sqmm 3 core 1100 volts grade incl taking down old one complete as specified and directed, m l for painting of incoming and outgoing pipes of oht sumps with standard colour code for ci pipe of sixe 100150 mm dia complete all as specified, m l for ms pipe of sise 150 mm dia with necessary bend tee weldding as required at size including necessary fittings to join with existing gici pipe lines complete all as specified and as directed, m l for ms pipe of sise 100 mm dia with necessary bend tee weldding as required at size including necessary fittings to join with existing gici pipe lines complete all as specified and as directed, m l ci fitting for bends any type radius and angle tapers any type straight bend increasing decreasing or double socket etc tee pieces single branch y junction double branch cross flange sockets or socket and spigot collars caps and plugs all complete all as specified and as directedsize up to 150 mm bore, sf in replacement butter fly valve in any positionof size 150 mm dia including rubber gasget nut bolts washers including taking down unserviceable valve complete all as specified and directed, sf in replacement nrv in any positionof size 100 mm dia including rubber gasget nut bolts washers including taking down unserviceable valve complete all as specified and directed, sf in replacement nrv in any positionof size 80 mm dia including rubber gasget nut bolts washers including taking down unserviceable valve complete all as specified and directed, sf in replacement nrv in any positionof size 65 mm dia including rubber gasget nut bolts washers including taking down unserviceable valve complete all as specified and directed, sf in replacement nrv in any positionof size 50 mm dia including rubber gasget nut bolts washers including taking down unserviceable valve complete all as specified and directed, supply fixing in and replacement of unserviceable automatic pressure switch for 1 hp to 2 hp booster pump all as specified and as directed, supply and fixing in replacement of surge tank booster tank suitable for booster pump including taking out the old one all as specified and as directed, supply and fixing in repalcement of manifolder connector asswembly for booster pump 5 way suitable for booster pump including taking out the old one all as specified and as directed, supply and fixing in repalcement of non return valve 25 mm for booster pump complete all as specifed and as directed, supply and fix in replacement of pressure gauge 0-5 kg cm2 for booster pump complete all as specified and as directed, supply and fix in replacement of motor of capacity 07510 hp for booster pump complete all as specified and as directed, supply and fixing of pressure booster pump 05 hp 10 hp 037kw 075kwrated voltage 220v voltage range 180v-260v 1ph rated frequency 50hz pipe size 25mm x 25mm max head up to 55 meters max discharge up to 4280 lph provided stainless steel insert for corrosion free stuck free operationhigh suction capacity instant suction up to 80 meters suction lift high grade brass impeller high grade electrical stamping reduces electrical losses improves pump effciencyeasy for maintenance make kirloskar crompton greaves havells, m l for dismantling of existing damaged valve pit complete and costruction of new brick masonary valve pit chamber of size 600 x 600 x 600mm internaldimensionincluding pcc brickwork and ms sheet cover 20 mm thick ms angle iron frame size 25mm x 25mm x 6mm around of valve pit locking arrangement with painting all steel surfaces with two coats of sythetic enamel paint over a coat of red oxide primer complete all as specified and directed, supply and fix in replacement panel mount digital voltmeter 0-500 volt complete, supply and fix in replacement panel mount digital ammeter 0-50 amp complete, supply and fix in replacemnet led type indicating lamp complete, supply and fix in replacemnet cts 50 5 amp complete, supply and fix in replacemnet cts 100 5 amp complete, yield test for the existing bore well by continuously pumping for 16 hours to determine safe pumping yield and submit the test report, ml for structural steel channels pcc foundationbase frame for motor of capacity upto 10hp including nuts bolts washer welding drilling hole for bolts bending in any shape or size as indicated or directed and inclusive of one coat of aluminium primer one under coat and one finishing coat of aluminium paint etc complete all as specified and as directed, ml for structural steel channels pcc foundationbase frame for motor of capacity 40hp50hp including nuts bolts washer welding drilling hole for bolts bending in any shape or size as indicated or directed and inclusive of one coat of aluminium primer one under coat and one finishing coat of aluminium paint etc complete all as specified and as directed
AI summaryBid / No Bid DecisionGenerate annexuresDraft Full Bid
LOADING...
