a. supplying, erecting, testing and commissioning of diesel generating set with alternator of kva alternator confirming to cpcb-iv plus emission compliant output continuous rating, phase, 415 4, 508/9 0.8 p. f. a.c supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable bhp at 1500 rpm with 10% overload for hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system
ng at 1500 rpm as per is 4722-2001 with voltage regulation +/- 5%, with performance class ge and maximum fuel consumption 14 ltr/hr @75% loading. both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite acoustic enclosure as fully assembled integral unit made of 16 swg crca sheet, sound absorbing material to restrict sound level up to 75 db at 1.0 m, provided with first filling of oil, diesel not less than 230 ltr etc. on provided m 20 grade cc foundation as per spec. no. gen-dg 2. supply, installation, testing & commissioning of ese lightning arrestor, controlled early streamer emission air terminal (eseat) with following specification: protecting radius 107 mtr with suitable mast height, with triggering time of 60 micro seconds as per nfc 17 - 102 which emits local electrostatic field that develops naturally around the shaft as thunderstorm begins to gather, the air terminal shall be tested to support a 100 ka current (wave form 10/350 us). test to be performed in compliance with nfc 17 102 or equivalent standards. the eseat should be able to work in both (positive and negative) lightning polarities. eseat shall be in strict compliance with the new test guidelines as per 'annex c' of the revised nfc 17 102 version 2011 for ese lightning protection system. the eseat shall be made of stainless steel 3048/316 grade non corrosive metallic components, electronic circuit, capacitor bank, transformer amplifier, sensor etc. to generate the streamer. the device to be a fully autonomous system requiring no external power supply. testable on site, using proprietary testers. the eseat should be sustainable designed to mitigate its environmental impact. complete as required. 3. supply, installation, testing and commissioning of main lt panel requirements panel with 16 swg, tank processed, epoxy powder coated. cable entry from top & out from top side of panel. the minimum sizes of sections of bus bars are given in table. each phase dually covered with red, yellow, blue and black color heat shrink sleeves. the panel should be should be outdoor type & floor/wall mountable with ip-42. name tag plates should be provided as per the requirement. paint -seminice gray powder coating. the panel should be inspected & tested at manufacturing place before dispatch at site. all incomer feeders with r, y, b phase indicating lamp & imp meter panel details. 4. providing & erecting hot dipped galvanized raceway with cover manufactured from 16 swg (1.6 mm thick) gi sheet of 200 mm width & 50 mm height complete with necessary coupler plates & hardware. 5. providing & erecting hot dipped galvanized raceway with cover manufactured from 16 swg (1.6 mm thick) gl sheet of 100 mm width & 50 mm height complete with necessary coupler plates & hardware. 6. providing & erecting hot dipped galvanized junction box manufactured from 18 swg (1.2 mm thick) gi sheet of 200 mm x 200 mm complete with necessary cover plates & hardware. 7. providing & erecting hot dipped galvanized junction box manufactured from 18 swg (1.2 mm thick) gi sheet of 300 mm x 300 mm complete with necessary cover plates & hardware. 8. xd/xs - supplying, fixing and commissioning of surface mounted spotlight with integrated ring raster ip with ral finish led w, k cct, gai >, body made of die cast aluminium deg, deg, deg medium beam having minimum cbcp value of effective delivered lumens -, macadam step , glare rating ugr<, lifespan to hrs, l&b ratio l70/b10 with lumen maintenance lm80, cri 90 including dali driver. standard warranty years. similar to bega make 85020 (prior approval from engineer change) 9. xu - supplying, fixing and commissioning of customized deep mala light ip with ral finish led -w, -k cct, diffused beam, macadam step , glare rating ugr<, lifespan hrs,, l&b ratio l/b with lumen maintenance lm, cri including dali 10. driver. standard warranty years. similar to bconnect - customize (prior approval from engineer change) 11. xj-supplying, fixing and commissioning of meter surface mounted linear luminaire having ip66 with aluminum body for installation. led 12-14 w/m 3000k cct diffused optic, real lumens: 700-800 real im/m. operating voltage: 24vdc, macadam step 3, glare rating ugr<19, lifespan: 60000 10 90000 hrs, ambient temperature -+40 c, l&b ratio l80b20 with lumen maintenance lm80 cri 90 including dali driver. standard warranty 6 years. similar to phos make nf-9.4410-tv-27-90-67-24-cm (prior approval from engineer inchange) 12. xp2 supplying, fixing, testing and commissioning of post top luminaire with ip65 and ik10 protection, ral powder-coated finish, comprising 40w led, 2200k cct, symmetrical beam optics, and an effective delivered output of 2000-2200 lumens. the luminaire shall have macadam step 3 color consistency, ugr < 19, cri 280, 880/20 lumen maintenance, lm-80 compliant leds, and a rated life of 60,000-90,000 hours at an ambient temperature up to 40c. the luminaire shall be manufactured from die cast aluminum (uni en 1706) with pmma frosted basket screen and stainless steel powder-coated components. including 4.0 m pole complete with foundation and earthing arrangement. the luminaire shall carry a minimum 5-year standard warranty and shall be similar to neri make - light 600, subject to prior approval of the engi.-in-charge. 13. xs/xd? - supplying, fixing and commissioning of surface mounted adjutable downlight with integrated ring raster ip 65 with ral finish led 24w, 3000k cct, gai >90, medium 30 deg beam having minimum cbcp value of 6180 candella. effective delivered lumens 2000-2200, macadam step 2, glare rating ugr<19, lifespan 60000 10 90000 hrs,, l&b ratio l70/b10 with lumen maintenance lm80, cri 90 including dali driver. standard warranty years. similar to bega make 84953 (prior approval from engineer inchange) 14. xs - supplying, fixing and commissioning of adjustable surface mounted projector light with integrated ring raster ip 65 with ral finish led 36w, 3000k cct, gai >90, medium 30 deg beam having minimum cbcp value of 9300 candella. body made of die cast aluminum. effective delivered lumens 3000-3200, macadam step 2, glare rating ugr<19, lifespan 60000 10 90000 hrs,, l&b ratio l70/b10 with lumen maintenance lm80, cri 90 including dali driver. standard warranty 6 years. similar to bega make 84954 (prior approval from engineer inchange) 15. xv supplying, fixing and commissioning of meter surface mounted linear grazer with antiglare louvers ip rated die cast aluminium body with adjustable brackets, led wattage to be w/m k cct garzer deg optic, macadam step . remote dali dimmable, delivered lumens: real 1200lm/m, glare rating ugr<19 l&b ratio l70/b10 with lumen maintenance lm80, cri 90. standard warranty years. similar to phos make db-na-lb-3000 27-20-on/ooff-b2 (prior approval from engineer inchange) 16. idp supply, fabrication, and installation of a custom-made heritage chandelier of diameter 2000 mm and height 2000 mm, made from heavy-duty metal frame with antique brass / bronze / gold leaf finish as approved by the architect. the chandelier shall include precision-cut k9 /lead crystal elements in pendants, prisms, and beads, arranged in multi-layer form to create a grand decorative effect. fixture shall be suitable for e14 / e27 led lamps or integrated led modules, providing warm white light (2700-3000k). suspension shall be with heavy-duty chain/rod system and canopy plate designed to safely carry the total load with 3x safety factor. all wiring shall be flame-retardant copper with proper earthing. the chandelier shall comply with iec/is standards and be supplied with shop drawings, finish samples, and load details for approval. minimum warranty: 3 years. (prior approval from engineer change) 17. xs supplying, fixing and commissioning of adjustable mini surface mounted spotlight with integrated ring raster ip65 body to be made of die cast aluminum with ral finish led 2w, 3000k cct, narrow 15 deg beam. effective delivered lumens 150-200, macadam step, glare rating ugr<19, lifespan 60000 to 90000hrs,, l&b ratio l70/b10 with lumen maintenance lm80, cri including dali driver. standard warranty years. similar to iguzzini make q683 (prior approval from engineer inchange) 18. xs - supplying, fixing and commissioning of adjustable surface mounted projector light ip65 with ral finish led 45w, rgba cct, macadam step 3, glare rating ugr<19, lifespan 60000 to 90000 hrs, ambient temperature 25 c, l&b ratio l80/b20 with lumen maintenance lm80, cri 80 including dmx driver. standard warranty years. similar to bega make 84964 (prior approval from engineer inchange) 19. xv supplying, fixing and commissioning of meter floor recessed linear grazer having ip67 rating & ik08 rating with aluminum body for installation. led w/m rgba cct, grazer optic (10), real lumens: 1510 im/m. macadam step 3, glare rating ugr<19, operating voltage: 220-240v, lifespan 60000 to 90000 hrs, ambient temperature -+40 c, l&b ratio l80/b20 with lumen maintenance lm80, cri 80 including dmx driver. additional mounting accessories: antiglare lou our louvres. standard warranty years. finish of the luminaire shall be matched with location from the architectural point of view. similar to phos make lbw75-45wa12-rgbw (prior approval from engineer inchange) 20. xp-supply, installation, testing and commissioning of adjustable gobo projector light, 160w, flat-field, high-contrast image projection 5,200 lumens output across the entire zoom range efficient optical system with integrated 150 450 zoom system configurable design for reduction of resources, cost, and weight one gobo or four gobo modules animation module manual framing module for precise framing of projected image 0-100% electronic dimming hibernation mode for very low power consumption compact and slim design rdm and dmx control local diagnostics and focusing via magnetic sensor dedicated compartment for install of power and dmx in/out cables optional pd hybrid in/out cable solution for easy daisy-chain automatic thermal management for safe operation in high and low ambient temperatures fully-weatherized housing (ip66, ik08 and c-4 high corrosion rating) shipped in fsc-certified cardboard packaging thermal cooling: convection and forced air (temperature regulated) maximum surface temperature: 60c (140 f) maximum ambient temperature (ta max.): 45 c (113 f) minimum ambient temperature (ta min.): -30 c (-22 f) standard warranty 5 years. similar to martin make exterior projection pro compact (prior approval from engineer inchange) 21. supply, installation, testing & commissioning of international see touch qs wallstation insert w 10 button with raise/lower qswe-brl 22. supply, installation, testing & commissioning of dali dimming controller; controls 2 independent 23. dali links with up to 64 dali ballasts per link. can take care of color tunable fixtures. groups of sensors inputs: occ sensor, daylight sensor and ir sensor. requires mains/line voltage feed similar to lutron qsn-2unvdal-d 24. supply, installation, testing & commissioning of switching module with channels, each channel with minium amp rating with provisions of sensors inputs: occ sensor, daylight sensor and ir sensor. requires mains/line voltage feed similar to lutron qsne-4 5230d module 25. the qse-ci-dmx control interface allows zones on a to control dmx512-controlled devices any zone can be mapped to either a single dmx512 channel or to three separate dmx512 channels, for rgb/cmy color-control the dmx channels (maximum of 32) are mapped to zones, and can be programmed as-channel lighting, ?-channel integration, or ?-channel rgb/cmy 26. supply, installation, testing & commissioning of central processor assembled processor with one/two configurable links and inbuilt bacnet for occupancy status. each processor link can be configured to be a dimmer link, shade link, or dimmer power panel link. processor accpets 2202404, 1 phase, 2 wire, 10 a feed, (throiugh power supply) similar to lutron athena 27. supply, installation, testing & commissioning of power supply unit for supply pdus to antenna devices similar to lutron qsps-dh-1-75 28. sitc of lighting control and monitor software, captures floor wise consumption, each event, energy reporting & monitoring per processor, 29. sitc of lighting control bacnet softwares for bms integration. this license for bacnet software enables a third-party building management system to control, monitor, and manage lights and shades in various areas on a processor. this license can also be used to share information between the control system and other control systems such as area occupancy, power usage, lighting state, etc. license required? per processor. 30. supply of qs cable for power and data simialr to lutron qs-cbl-lszh cable adheres to ce standards for low smoke generation (en 60332-1-2), halogen gas emission (en 61034-2), and flame retardation (en 60754 162). five conductors: common0.75 mm (18awg) power 0.75 mm (18 awg) mux data0.25 mm (22 awg) data 0.25 mm (22 awg) drain wire - 0.2 mm2 (24 awg) laying in suitable conduits to be done by electrical contractor. 31. supply, installation, testing & commissioning of enclosure db box, for housing lms backend devices such as processors and dimming modules. the enclosure shall include all necessary protection devices, including mcbs and rccbs, to ensure system and personnel safety. suitable for surface wall mounting in indoor technical spaces supply, installation, testing & commissioning of enclosure db box, for housing lms backend devices such as processors and dimming modules. the enclosure shall include all necessary protection devices, including mcbs and rccbs, to ensure system and personnel safety. suitable for surface wall mounting in indoor technical spaces. 32. programming of complete system the scope of work includes the complete programming, testing, and commissioning of the lighting management system (lms), covering configuration of lighting zones, dimming levels, sensors, and schedules as per the approved control philosophy, integration with bms/third-party systems if required, point to-point and functional testing of all devices, finetuning and calibration, preparation of test reports and as built documentation, and providing necessary training to client/end-user staff to ensure the lms is fully functional, compliant, and ready for handover. 33. supplying & erecting tb internal surveillance hdd suitable for sata port of nvr, interface transfer rate & gb/s, maximum sustained transfer rate 210 mb/sec to 213 mb/s. drive bay supported e<+, cameras supported up to 64, cache (mb) 256, load/unload cycle -3000000, work load rating per year 180tb, mtbf 1000000 hrs. https. rohs, ul, ce certified, dully erected in position in provided nvr as per specification no. cctv-hdd 34. supplying installing testing & commissioning of 32/40 ch network video recorder (nvr) suitable 35. connect min. 32 ip cameras up to 4 megapixel resolution with hdmi/vga outputs provided 36. at least one hdmi output of k resolution at least one vga output with output up to 192041080 37. support h.265 or higher h.264 mjpeg supports redundant dual power incoming bandwidth 320 38. mbps with minimum & sata ports anr technology & sata interfaces for hdds and capacity 39. of each hdd up to 4tb minimum 02 usb port alarm i/o 16/4 rj-4510/100/1000 mbps self adaptive 40. ethernet interface support multibrand network cameras onvif conformance multiple network 41. monitoring web viewer, support protocol tcp/ip dhcp dns ddns ntp sadp smtp nfs 42. iscsi upnpt https. rohs ul ce fcc certified. duly erected in provided u rack with 43. wiring connections tagging and programming etc. complete as per specifications no. cctv- 44. nvr [non csr] 45. supplying & erecting of high definition 4/5 megapixel ip ir varifocal bullet camera with following features image sensor minimum 1/2.8 progressive scan cmos video resolution minimum 2592 1520 video compression h.264 h.265 or higher at least three individually configurable stream frame rate minimum 25 fps at all resolutions. wdr minimum 120 db wide dynamic range onvif profile conformant minimum ir distance 50m lens type 2.8 - 13mm lens uto/motorized varifocal focal field of view horizontal fov 1030 to 32 vertical fov 73' to 240 diagonal fov 1420 to 40* lux sensitivity- minimum 0.2 lux at color minimum 0.05 lux at black & white ... lux (ir) night vision distance min ir- 50m camera minimum adjustment angles - pan 3500 tilt 720 rotate 3500, power supply support 12vdc & poe ip67 ik10 - vandal resistant built in micro sd/sdhc/sdxc card slot of min 128 gb built in microphone. minimum input/output- audio in x audio out x ? alarm in x alarm out x 1. image settings rotate mode saturation brightness contrast sharpness gain white balance. image enhancements day/night-auto (icr)/color/black & white d digital noise reduction automatic white balance automatic gain control backlight compensation highlight compensation. events privacy masking motion detection scene change detection face capture video tampering audio exception detection region entrance detection region exiting detection. operating temperature (-30 to 600 c). security- user account and password protection https ip filter ieee 802.1x digest authentication user access log tls1.2 aes-256 ssh/telnet closed ftp disabled. protocol- dhcp udp http https ntp dns rtp rtsp smtp ssl/tls tcp/ip secure real-time transport protocol (srtp) bonjour snmp and secure shell (ssh) supported protocol. rohs weee iso-14001 and reach compliant ul/en or equivalent bis/tech/stqc or any indian standards as applicable ce fcc certified. 46. supplying & erecting of high definition 4/5 megapixel ip ir ptz camera with following features 4/5 mp wdr 32x ir network ptz camera.1/2.8" or higher mp ps cmos image sensor max. 4mp (268841520) @25fps or above / max. 5mp (2880 x 1620) @25fps or above instastream, h. 265, h. 264, h.264b, h.264h, mjpeg support triple stream, storage sftp, nas, mirco sd card (upto 256gb) powerful 32x optical and 16x digital zoom wdr (120db), 2d nr/ 3d nr, day/night(icr), roi, defog, awb, blc up to 300 presets, 5 scan, 8 tour, pattern ir range of 150 mtr or above support poe, ip 65/67, ik10. 47. supplying & erecting 55" professional led display with 1920 1080 (full hd) display, suitable for 32/64 channel nvr and following features brightness: minimum 500 cd/m contrast ratio: minimum 1000:1 viewing angle: 178/178 deg. response time: maximum < ms inputs: hdmi, vga, bnc, usb, audio in, built-in speakers maximum ? w, suitable to operate on 100-240 450 hz ac supply and 24/7 duty cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. cctv-mon 48. supply, installation, testing and commissioning (sitc) of hp z2 tower g workstation with intel core i7-12700 processor (12 cores, 20 threads, up to 4.90 ghz, 25 mb cache), minimum 16 gb ddr5 ram (expandable), 512 gb pcie nvme ssd, intel uhd graphics 770 or better, gigabit ethernet, usb ports, audio ports, windows 11 professional (64-bit) pre-installed, usb keyboard and optical mouse, complete w with 21.5-inch full hd (1920 x 1080) led ips monitor, anti-glare display, hdmi/displayport connectivity, power cables and all necessary accessories, including installation, testing, commissioning and years onsite oem warranty, complete as directed by the engineer-in-charge. 49. supplying, installation, testing & commissioning of 15-watt premium-sound cabinet loudspeaker, high fidelity music and speech reproduction, selectable ohm, 70 v and 100 v inputs, abs enclosure, maximum power 22.5 w, rated power (phc) 15 w, power tapping - 15/7.5/3.75/1.9 w, sound pressure level at rated power / 1 w (1 khz, 1 m)- 99/87 db, effective frequency range-(-10 db) 95 hz to 20 khz, rated input voltage -11/70/100 v, rated impedance - 1326/667 ohm, transducers - 101.6 mm (40) woofer, 13 mm (0.51") dome tweeter, make-bosch/mipro/ev warranty years 50. supplying, erecting, testing & commissioning mixer amplifier 150w rms power with built-in digital player with remote and having 7 mic & aux inputs with box speaker/driver unit selector switch to each zone, stereo/mono switch, frequency response 50-15000 hz, output regulation <2db, serprate control for usb level. the unit shall have preamplifier and line output for connecting to booster amplifier and for recording the program with resettable circuit breaker for protection against overload and short circuit. the unit shall have speaker output range of 2-4-82/ (low impedance) and 70v & 100v/(high impedance) & it can instant transfer to dc power (36v) if ac power fails. signal to noise ratio between 60db to 80db. complete as per specification no. - 51. supplying and erecting abc powder type fire extinguisher as per is: 13849/15683 of 6 kg capacity with necessary clamp for erection on wall. (marathi image)
Description : tender estimated cost & dates are tentative only. please refer nit or tender document for precise information.
12
Days Left
Submission Date
Refer Document
Opening Date
30 SEP 2026
Tender Estimated Cost
Refer Document
EMD
Refer Document
Apply with Surety Bond
Tender Document Fees
Refer Document
AI Bid Assistant
Prepare a complete bid response for this tender in under 30 minutes.
Tender247 tries to ensure accurate & authentic tender information at its level best however it cannot be held responsible for Omissions, Errors, etc. Users are advised to refer to Tender Document published by Procuring entity before participating / submitting bid.
LOADING...
