FILTERS
mks-26-078 - widening of link road mallan to wara kishanpura compaction of earth work preparation of sub grade to premix carpet including construction of culvert drain providing and fixing of rodas structure road safety measure in m.c. gidderbaha work code 26078
View Insights
construction of dahisahi sub- minor including its all structures off- taking at rd 54393m from jambhira left main canal - earth work and structural work
strengthening of ohe through stone pitching, soil filling with raising of muffs including associated ohe modification works in connection with safety in bza division.
construction of various civil work i.e. control room building, t f plinth , equipment foundations, odct , u fencing, culvert, road, gravel, e/filling, 7ft ht boundary wall, sign board ,furniture and electrical appliances at 33 kv s/stn. cheeka.
mks-26-077 - construction of various link roads compaction of earth work preparation of sub grade to premix carpet including construction of culvert drain providing and fixing of rodas structure road safety measure in m.c. gidderbaha work code mks 26-077
resurfacing of various road under mmgsy (normal) in anand taluka dist : anand pkg. no. and/mmgsy/normal/np/res/2026-27/20- clearing and grubbing, earthwork for embankment, pre-cast interlocking concrete block, granular sub base, compacted wbm, reinforced concrete np3 pipe, built-up spray grout base, built-up spray grout base, bituminous macadam, mix seal surfacing, dismantling existing rcc structure, m-200 trimix cc road, hectometer, ordinary kilometer stone, cautionary warning sign, village name / bump ahead sign, direction sign (junction board), road marking with hot applied thermoplastic paint, cat eye (stimsonite), citizens information board, mmgsy logo board, mmgsy project information board, regulatory/mandatory signs, informatory signs, excavation for foundation, m-100 cement concrete, m-150 cement concrete, tmt bar fe500d reinforcement, weep hole, filter media.
construction including metalling and blacktopping of road byndihati (0.00 to 1.30 km)- earthwork, construction of hill side drain, construction of slab culvert, construction of retaining wall/breast wall and metalling and blacktopping
construction of farm land culvert over sara nalla near tanarada under belaguntha block. - earthwork, cement concrete, reinforced cement concrete, and rr stone works. earthwork, cement concrete, reinforced cement concrete, single under reamed piles and rr stone works
earthwork in restoration between km 0.000 to km 5.430 and brick soling on service road between km 0.000 to km 5.400 of jagdishpur minor in district santkabirnagar.
shifting of ohe mast and lt crossing in connection with construction of new major bridge no.- 47 (18x18.3m composite girder) over river dhadhar at km 33.087 between sarsu & oro statlon , minor bridges, rub, retaining wall, earthwork, blanketing and track linking in diversion on both approaches of major bridge to connect existing track in rajgir- tilaiya section.
corrigendum : improvement and protection work to saradhabali branch nalla for flood protection to berhampur town. - earthwork, cement concrete, reinforced cement concrete, and rr stone works. earthwork, cement concrete, reinforced cement concrete and rr stone works
guntakal division : sr.den/south jurisdiction : earth work / cess repairs in recouping the formation in isolated stretches for a quantity of 35222.50cum in sse/p.way/hx section.
corrigendum : modernization of various rural link road (from earth work upto premix carpet including constn. of culverts,drains,ret.walls and road furniture/safety measures ) under 555 cr project distt gurdaspur mc dbn g-3 (555 cr)
strengthening of ohe through stone pitching, soil filling in connection with safety in bza division.
works including grass laying, boundary wall construction, earth filling, footpath construction, installation of gates and grilles, and painting at the ramlila/late cds bipin rawat park in ward no. 29, rampark locality.
supplying and erection of precast earth retaining walls and backfilling of earth for engineering halls canteen at sea side, north site, barc, trombay, mumbai
construction including metalling and blacktopping of internal link road at lew rim puriang total length=0.398.km nature of work- earthwork, mbt works, protection works and drainage works.
works in the park located in ward no. 12 (khanna nagar/tyagi market), including grassing, boundary wall construction, earth filling, footpath construction, installation of gates and grilles, and painting/whitewashing.
mks-26-076 - construction of various link roads compaction of earth work preparation of sub grade to premix carpet including construction of culvert, drain providing and fixing of rodas structure road safety measure in m.c. gidderbaha work code 26076
work of repairing of valve chamber, ms fabrication, tubewell deepening and carriage of material, earth filling etc. works at various jjy (jawahar jyoti yojana) and regular schemes under junior engineer, rural section (16 nos. gram panchayats), sub-division newai, tonk under jurisdiction.
work of repairing of valve chamber, ms fabrication, tubewell deepening and carriage of material, earth filling etc., at various jjy and regular schemes under junior engineer, rural section (25 nos. gram panchayats), sub-division newai, tonk.
works including grassing, boundary wall construction, earth filling, footpath construction, gate and grill installation, and painting/whitewashing in the park near pump no. 3 (cwr) in ward no. 12, khanna nagar.
works in the park located in ward no. 33 (opposite jodhpur sweets, dlf locality), including grass laying, boundary wall construction, soil filling, footpath construction, installation of gates and grilles, and painting/whitewashing
construction of govt degree college at banihal (by way of construction of approach road by way of earth work cutting and walling - refer to boq
construction work involving the boundary wall, soil filling, hume pipe culvert, and pcc path at the mrf site.
providing walking track, gym play equipment badminton court and volleyball court at yadava jaggarajupeta park in ward.no.88 of pendurthi zone area of gvmc - engaging of front end loader for jungle clearnace and including cost and conveyance of all materials and labour charges as per ss and as directed by the department officers, engaging of tipper for conveynace of debries and waste materials from site to dummping yard etc., complete as per ss and as directed by the dept. officer, earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational incidentalm labour charges such as shoring, sheeting, planking, struting, etc, complete for finished item of work including seigniorage exclduing dewatering charges etc, per ss - 20 b (apss 308), filling with stone crusher dust in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including all operational, incidental, labour charges, seignorage charges, hire charges of t & p etc., complete for finished item of work., plain cement concrete (1:4:8) proportion (cement: fine aggregate: coarse aggregate) using 40mm size hard broken granite (is383, 1970) machine crushed metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, mixing concrete in concrete mixer including all materials, all operational, incidental, and labour charges such as laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work., brick masonry in cm (1:8) with with flyash cement solid bricks of size 290x225x140mm having a compression test not less than 50 kg/sqcm including cost and conveyance of all materials, seigniorage charges and labour charges for mixing of mortor watering curing etc. complete., collection of gravel from approved quarry including cost, conveyance and seignerage charges including, stacking at site to departmental gauge spreading, sectioning with rolling charges etc complete - 1 cum, plain cement concrete grade m20 - nominal mix (cement fine aggregate: coarse aggregatge) corresponding to table 9 of is 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including seignorage chargers, sales & other taxes on all materials including all operational, incidental and labour charges such as machines mixing, laying concrete, curing etc., complete as per ss, plastering in cement mortar (1:3) 12mm thick watering for curing including cost of materials, scafolding and watering and conveyance of all materials and all labour charges etc., complete as per ss and as directed by the engineer - in - charge., painting two coats with acrylic exterior emulsion paint having voc (volatile organic compound ) content less than 50 grams/ liter over plastered surface for external walls including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., supply fabrication of steel (structural) and erection of ms space frame structure with supplyting, fabricating installing the roof stucture in structural steel with necessary curvature as including cost and conveyaance, watering, tamping including all labour charges, providing hdpe net 2.5mm thick including all materials and labour charges etc.,, roofing with pre-painted galvalume trapezoidal profile roofing sheets with 0.50mm thickness, coating: alu-zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness (top): 18 to 20 microns, (bottom): 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours - for dome cap type roofing fixed over the ready made steel roof structure having a bottom diametre of 36.4 metres and rise of 4.0 metres., flooring with high polished granite slabs ... mm thick other than black set over base coat of cement mortar (1:4), 20 mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like cement, sand water and tilesetc., complete, including seigniorage charges, labour charges for dressing of, formation of 150 mm thick (consolidated) walking track layer using red earth@60%,crusher dust@30% & saw dust@10% mixed thoroughly homogeneous and spreading to even surface and consolidation with hand roller and watering etc.complete finished item of work as per instructions of the department.true to uniform gradients to the possible extent., providing rcc well rings for 1.2m x 0.30m including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court poles and volley ball court poles including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court and volley ball court nylon nets including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., providing and laying of interlocking concrete block pavements of glass fibre reinforced concrete pavers of size 225 x 175 mm and thickness of not less than 60mm heavy duty conforming to is 15658:2006 including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., "malty activity play system ( special ), descriptions, ? product area : 32ft x 19ft, ? safe play area : 21ft x 42 ft, ? age group: 5-14 yrs., ? friends at a time : 15 to 18, ? platform height : 3 ft,5ft & 7f", "net rock climber 2.1 metres( pgsl 30 ), in this net rock climber pad: rock climber 7ft. pad made from fibber reinforced plastic, (frp) attached to the angular frame. the pad is provided with rock shaped part, ergonomically spaced in zigzag manner for climbing act.", "twindler go round( pgmr 01), railings: the four railings made from 15nb galvanized pipe conforming to is 1239(part, 1):1979 fixed to frp platform at one end and the other end fixed to the platform frame., platform: twindler mgr platform made from gi coated framed structure mated to fibre, reinforced plastic over the top to form a specially designed curved platform", "single board abs with centre pipe & prime, stand sleeve shall be minimum of 100mm nb dia of thickness not less than 5.00mm,footrest support & sit up board support pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm, handle frame & seat frame support shall be minimum of 24mm nb die of thickness not less than 3.6mm & connecting link pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. sit up board made with high quality frp / ss304 perforated material. all pipes shall be uniformly powder coated up to minimum 90 microns hickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed steel for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms. with one year warranty.", aero rider with main frame shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & connecting link pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the handle frame are hinged over 100nb main frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat s are made with the hdpe sheet of size. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and t. with one year warranty, hand rower with base link pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, upper link pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm & connecting links & handle links pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns ionized coated and zinc dipped joint with robotic welded. the handle frame are hinged bearings should be reputed make and press fitted for smooth rotation, and does not require republication i.e., maintenance - free ball bearing. seat rest is made with the lldpe sheet of with uniform bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb die supported with m.s. angle the solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and. with one year warranty., shoulder exerciser double with prime stand pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & connecting links shall be minimum of 25mm nb die of thickness not less than 3.60mm are of 'c' class heavy grade make with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the two handle frames are hinged over 100nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat & back rests are made with the lldpe with uniform bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and. with one year warranty, "ovate stepper with prime stand pipe shall be, minimum of 80mm nb dia of thickness not less than 4.50mm, pedal link pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm, handle frame pipes shall be minimum of 32mm nb dia of thickness not less than 3.60mm and handle grips shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade of with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the pedal frame are hinged over 80nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re lubrication i.e., maintenance - free ball bearing. foot rest shall be made of. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. the all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty.", "aerial stroller double with three prime stand pipes shall be minimum of 100mm nb dia of thickness not less than 5.00mm, pedestal frame shall be minimum of 32mm nb dia of thickness not less than, 3.6mm & handle frame shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade make with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the two pedestal frames are hinged over 100nb prime stand pipes with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re- lubrication i.e., maintenance -free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty", "chest press double with prime stand pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than, 3.6mm & connecting links shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns ionized coated and zinc dipped joint with robotic welded. the two handle frames are hinged over 100nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat & back rests are made with the lldpe bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle 25x25x4mm. poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and to with one year warranty", tripple twister with prime pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, standing twister plate support pipe shall be minimum of 80mm nb dia of thickness not less than 4.5mm, bottom frame support shall be minimum of 32mm nb dia of thickness not less than 3.6mm & handle ring shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the twister plate is hinged over 80nb standing pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipes with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, fore arm twirl double with centre pipe shall be of minimum 100mm nb dia of thickness not less than 5.00mm, support frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & tai chi spinner rings shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 75 microns zinc dipped joint with robotic welded with handle knobs are made from high quality nylon material. the rings are hinged over 32nb support frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed by for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 90mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, sky walker double with main frame shall be minimum of 100mm nb dia of thickness not less than 4.50mm & handle pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded with plastic/rubber grips on top end. the handle pipes are hinged over 40nb main frame with the help of especially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e. maintenance - free ball bearing. the handle pipes shall be further extended to the 24mm nb dia on both sides. paired rectangular tubes with four foot rests are linked to main frame. foot rest shall be made of aluminium material - .. all pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be deep with minimum of 100mm nb dia supported with m.s. angle the instruction plate of size of ss 304 grade plate with with your company emblem at two sides facing to users with printing. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, maintenance for open gym equipment for extra one year, providing cement concrete sitting benches including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply and delivery of 250mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., supply and delivery of 180mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., drilling of tube well with down the hole hammer drilling of finished dia meter of 165 mm dia in all formations of soils inclduing insertion of 180mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., drilling of tube well with down the hole hammer drilling of finished dia meter of 180 mm dia in all formations of soils inclduing insertion of 250mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., supply and transportation of 2.00 hp 25 stage three phase isi submersible motor pumpset suitable for 4" bore well. makes:kirloskar / crompton / texmo / cri / ksb/lubi including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-5.4.1), labour charges for fixing of submersible motors including cost of all materials and all charges etc complete, supply of 3 core 2.5 sqmm flat copper cable as per is694:1990 for submersible motors.makes: finolex / polycab / havells / v-guard / goldmedal / gm / million / vimal / nandicab / kundan cab/hi-tech including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-1.6.3) (elec-1.6.3), fabrication , transportation and supply of suitable size panel board for single phase submersible motor 2 to 3hp consisting of relay, contactor, starting and running capacitors, voltmeter, ammeter, indicator lamps, mcb , on/off switch including supply and fixing of dol starter of make c&s/l&t/seimens/bch/crompton. complete.,.including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. elec-5.4.16, manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 6kg/sqcm (vide page no-86/item no-1 of public health items of cssr - 63 mm diametre complete as per ss and as directed by the departmental officers., manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 10kg/sqcm - 63 mm diametre complete as per ss and as directed by the departmental officers., providing independent earthing by exacavating a pit to a depth of 2.25mtr in all soils as per size specified in the data for important equipment with 2.5mtr length 40mm dia 'b' class g.i pipe and 18" dia 3" thick hume pipe ring with r.c.c. slab cover duly providing staggered holes filling with 20kg salt and 40kg charcoal or 40kg bentonite powder from the bottom of the pipe giving earth connection from electrode through g.i strip of 25 x 6mm x 200mm length to be bolted with nut bolts including supply and termination of no.8 g.i.wire from bottm of the pipe with all accessories and labour charges complete, as per is specifications 732/198 and as directed by engineer incharge, fiber casting, also known as frp (fiber reinforced plastic) sculpture, is a technique where a liquid resin is poured into a mold to create a three-d object, often a statue. the process typically involves creating a clay model, taking a rubber mold, mixing resin with chalk powder and fiber liquid, pouring the mixture into the mold, and then curing and finishing the resulting fiber sculpture and including cost and conveyance of all materilas and all labour charges etc., complete as per ss and as instructed by the departmental engineer - in charge.(rabbits ,dears, budha statues ), making inauguration arrangements including cost of plaque and its fixing , chairs, shamiyanas, gralands and puja samagri and water bottles etc., operations complets as per ss.
horticulture service - lumpsum based - general maintenance of gardenlawnfieldnurserypark; site clearing, planting treesplantsgrass, soil preparation, general maintenance of plant (mowing, strimming, laying, sweeping, watering, weeding), applyin..
work of earth filling within the premises of 50 tpd solid waste processing facility, ward number 14, vats nagar, mohalla korro.
earth filling work in the premises of kanha gaushala under construction in ward number 17, gautam buddh nagar, khora mohalla.
works in the park at ward no. 12, rameshwar park extension, including grassing, boundary wall construction, earth filling, footpaths, gate and grill installation, painting, etc.
works at the triangular park in ward no. 12, khanna nagar locality, including grassing, boundary wall construction, earth filling, footpath construction, installation of gates and grilles, and painting.
works including grass laying, boundary wall construction, earth filling, footpath construction, gate and grille installation, and painting at chhath park (near the old water tank and shiv mandir, dlf colony, ward no. 33).
earth work in forming embankment, laying of bg track, points & crossing for provision of spur line at nagore station.
works at gurjar park in ward no. 1 (mohalla milak gaon), including grass laying, boundary wall construction, earth filling, footpath construction, installation of gates and grilles, and painting/whitewashing.
works in the park at ward no. 12, mohalla tyaga market, including grass planting, boundary wall construction, soil filling, footpath construction, installation of gates and grilles, and painting.
works including grass laying, boundary wall construction, earth filling, footpath construction, gate and grille installation, and painting/whitewashing in the park near pump no. 2, khanna nagar (ward no. 12).
works including grassing, boundary wall construction, earth filling, footpath construction, gate and grille installation, and painting at the ancient shiva temple park in the dlf neighborhood (ward no. 33).
exterior works of archaeological museum, kondapur, sangareddy district, 2026-27- execution of work - earthwork excavation in all kind of soil, rock for laying pcc, providing granite benches, pathways, installing solar powered led post light, providing parking with cc interlocking paver block
providing play equipment, badminton court, cricket court at vuda colony park in ward.no.97 of pendurthi zone area of gvmc - engaging of front end loader for jungle clearnace and including cost and conveyance of all materials and labour charges as per ss and as directed by the department officers, engaging of tipper for conveynace of debries and waste materials from site to dummping yard etc., complete as per ss and as directed by the dept. officer, collection of gravel from approved quarry including cost, conveyance and seignerage charges including, stacking at site to departmental gauge spreading, sectioning with rolling charges etc complete - 1 cum, earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational incidentalm labour charges such as shoring, sheeting, planking, struting, etc, complete for finished item of work including seigniorage exclduing dewatering charges etc, per ss - 20 b (apss 308), filling with stone crusher dust in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including all operational, incidental, labour charges, seignorage charges, hire charges of t & p etc., complete for finished item of work., plain cement concrete (1:4:8) proportion (cement: fine aggregate: coarse aggregate) using 40mm size hard broken granite (is383, 1970) machine crushed metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, mixing concrete in concrete mixer including all materials, all operational, incidental, and labour charges such as laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work., brick masonry in cm (1:8) with with flyash cement solid bricks of size 290x225x140mm having a compression test not less than 50 kg/sqcm including cost and conveyance of all materials, seigniorage charges and labour charges for mixing of mortor watering curing etc. complete., plain cement concrete grade m20 - nominal mix (cement fine aggregate: coarse aggregatge) corresponding to table 9 of is 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including seignorage chargers, sales & other taxes on all materials including all operational, incidental and labour charges such as machines mixing, laying concrete, curing etc., complete as per ss, plastering in cement mortar (1:3) 12mm thick watering for curing including cost of materials, scafolding and watering and conveyance of all materials and all labour charges etc., complete as per ss and as directed by the engineer - in - charge., painting two coats with acrylic exterior emulsion paint having voc (volatile organic compound ) content less than 50 grams/ liter over plastered surface for external walls including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., supply fabrication of steel (structural) and erection of ms space frame structure with supplyting, fabricating installing the roof stucture in structural steel with necessary curvature as including cost and conveyaance, watering, tamping including all labour charges, providing hdpe net 2.5mm thick including all materials and labour charges etc.,, roofing with pre-painted galvalume trapezoidal profile roofing sheets with 0.50mm thickness, coating: alu-zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness (top): 18 to 20 microns, (bottom): 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours - for dome cap type roofing fixed over the ready made steel roof structure having a bottom diametre of 36.4 metres and rise of 4.0 metres., flooring with high polished granite slabs ... mm thick other than black set over base coat of cement mortar (1:4), 20 mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like cement, sand water and tilesetc., complete, including seigniorage charges, labour charges for dressing of, formation of 150 mm thick (consolidated) walking track layer using red earth@60%,crusher dust@30% & saw dust@10% mixed thoroughly homogeneous and spreading to even surface and consolidation with hand roller and watering etc.complete finished item of work as per instructions of the department.true to uniform gradients to the possible extent., providing rcc well rings for 1.2m x 0.30m including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court poles and volley ball court poles including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court and volley ball court nylon nets including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., providing and laying of interlocking concrete block pavements of glass fibre reinforced concrete pavers of size 225 x 175 mm and thickness of not less than 60mm heavy duty conforming to is 15658:2006 including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., "malty activity play system ( special ), descriptions, ? product area : 32ft x 19ft, ? safe play area : 21ft x 42 ft, ? age group: 5-14 yrs., ? friends at a time : 15 to 18, ? platform height : 3 ft,5ft & 7f", "net rock climber 2.1 metres( pgsl 30 ), in this net rock climber pad: rock climber 7ft. pad made from fibber reinforced plastic, (frp) attached to the angular frame. the pad is provided with rock shaped part, ergonomically spaced in zigzag manner for climbing act.", "twindler go round( pgmr 01), railings: the four railings made from 15nb galvanized pipe conforming to is 1239(part, 1):1979 fixed to frp platform at one end and the other end fixed to the platform frame., platform: twindler mgr platform made from gi coated framed structure mated to fibre, reinforced plastic over the top to form a specially designed curved platform", providing cement concrete sitting benches including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply and delivery of 250mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., supply and delivery of 180mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., drilling of tube well with down the hole hammer drilling of finished dia meter of 165 mm dia in all formations of soils inclduing insertion of 180mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., drilling of tube well with down the hole hammer drilling of finished dia meter of 180 mm dia in all formations of soils inclduing insertion of 250mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., supply and transportation of 2.00 hp 25 stage three phase isi submersible motor pumpset suitable for 4" bore well. makes:kirloskar / crompton / texmo / cri / ksb/lubi including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-5.4.1), labour charges for fixing of submersible motors including cost of all materials and all charges etc complete, supply of 3 core 2.5 sqmm flat copper cable as per is694:1990 for submersible motors.makes: finolex / polycab / havells / v-guard / goldmedal / gm / million / vimal / nandicab / kundan cab/hi-tech including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-1.6.3) (elec-1.6.3), fabrication , transportation and supply of suitable size panel board for single phase submersible motor 2 to 3hp consisting of relay, contactor, starting and running capacitors, voltmeter, ammeter, indicator lamps, mcb , on/off switch including supply and fixing of dol starter of make c&s/l&t/seimens/bch/crompton. complete.,.including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. elec-5.4.16, manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 6kg/sqcm (vide page no-86/item no-1 of public health items of cssr - 63 mm diametre complete as per ss and as directed by the departmental officers., manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 10kg/sqcm - 63 mm diametre complete as per ss and as directed by the departmental officers., providing independent earthing by exacavating a pit to a depth of 2.25mtr in all soils as per size specified in the data for important equipment with 2.5mtr length 40mm dia 'b' class g.i pipe and 18" dia 3" thick hume pipe ring with r.c.c. slab cover duly providing staggered holes filling with 20kg salt and 40kg charcoal or 40kg bentonite powder from the bottom of the pipe giving earth connection from electrode through g.i strip of 25 x 6mm x 200mm length to be bolted with nut bolts including supply and termination of no.8 g.i.wire from bottm of the pipe with all accessories and labour charges complete, as per is specifications 732/198 and as directed by engineer incharge, making inauguration arrangements including cost of plaque and its fixing , chairs, shamiyanas, gralands and puja samagri and water bottles etc., operations complets as per ss.
providing walking track, gym play equipment, badminton court at sai ram layout park in ward.no.96 of pendurthi zone area of gvmc - engaging of front end loader for jungle clearnace and including cost and conveyance of all materials and labour charges as per ss and as directed by the department officers, engaging of tipper for conveynace of debries and waste materials from site to dummping yard etc., complete as per ss and as directed by the dept. officer, earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational incidentalm labour charges such as shoring, sheeting, planking, struting, etc, complete for finished item of work including seigniorage exclduing dewatering charges etc, per ss - 20 b (apss 308), filling with stone crusher dust in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including all operational, incidental, labour charges, seignorage charges, hire charges of t & p etc., complete for finished item of work., plain cement concrete (1:4:8) proportion (cement: fine aggregate: coarse aggregate) using 40mm size hard broken granite (is383, 1970) machine crushed metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, mixing concrete in concrete mixer including all materials, all operational, incidental, and labour charges such as laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work., brick masonry in cm (1:8) with with flyash cement solid bricks of size 290x225x140mm having a compression test not less than 50 kg/sqcm including cost and conveyance of all materials, seigniorage charges and labour charges for mixing of mortor watering curing etc. complete., plain cement concrete grade m20 - nominal mix (cement fine aggregate: coarse aggregatge) corresponding to table 9 of is 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including seignorage chargers, sales & other taxes on all materials including all operational, incidental and labour charges such as machines mixing, laying concrete, curing etc., complete as per ss, plastering in cement mortar (1:3) 12mm thick watering for curing including cost of materials, scafolding and watering and conveyance of all materials and all labour charges etc., complete as per ss and as directed by the engineer - in - charge., painting two coats with acrylic exterior emulsion paint having voc (volatile organic compound ) content less than 50 grams/ liter over plastered surface for external walls including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., supply fabrication of steel (structural) and erection of ms space frame structure with supplyting, fabricating installing the roof stucture in structural steel with necessary curvature as including cost and conveyaance, watering, tamping including all labour charges, roofing with pre-painted galvalume trapezoidal profile roofing sheets with 0.50mm thickness, coating: alu-zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness (top): 18 to 20 microns, (bottom): 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours - for dome cap type roofing fixed over the ready made steel roof structure having a bottom diametre of 36.4 metres and rise of 4.0 metres., flooring with high polished granite slabs ... mm thick other than black set over base coat of cement mortar (1:4), 20 mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like cement, sand water and tilesetc., complete, including seigniorage charges, labour charges for dressing of, formation of 150 mm thick (consolidated) walking track layer using red earth@60%,crusher dust@30% & saw dust@10% mixed thoroughly homogeneous and spreading to even surface and consolidation with hand roller and watering etc.complete finished item of work as per instructions of the department.true to uniform gradients to the possible extent., providing rcc well rings for 1.2m x 0.30m including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court poles and volley ball court poles including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court and volley ball court nylon nets including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., providing and laying of interlocking concrete block pavements of glass fibre reinforced concrete pavers of size 225 x 175 mm and thickness of not less than 60mm heavy duty conforming to is 15658:2006 including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., "malty activity play system ( special ), descriptions, ? product area : 32ft x 19ft, ? safe play area : 21ft x 42 ft, ? age group: 5-14 yrs., ? friends at a time : 15 to 18, ? platform height : 3 ft,5ft & 7f", "net rock climber 2.1 metres( pgsl 30 ), in this net rock climber pad: rock climber 7ft. pad made from fibber reinforced plastic, (frp) attached to the angular frame. the pad is provided with rock shaped part, ergonomically spaced in zigzag manner for climbing act.", "twindler go round( pgmr 01), railings: the four railings made from 15nb galvanized pipe conforming to is 1239(part, 1):1979 fixed to frp platform at one end and the other end fixed to the platform frame., platform: twindler mgr platform made from gi coated framed structure mated to fibre, reinforced plastic over the top to form a specially designed curved platform", "single board abs with centre pipe & prime, stand sleeve shall be minimum of 100mm nb dia of thickness not less than 5.00mm,footrest support & sit up board support pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm, handle frame & seat frame support shall be minimum of 24mm nb die of thickness not less than 3.6mm & connecting link pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. sit up board made with high quality frp / ss304 perforated material. all pipes shall be uniformly powder coated up to minimum 90 microns hickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed steel for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms. with one year warranty.", aero rider with main frame shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & connecting link pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the handle frame are hinged over 100nb main frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat s are made with the hdpe sheet of size. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and t. with one year warranty, hand rower with base link pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, upper link pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm & connecting links & handle links pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns ionized coated and zinc dipped joint with robotic welded. the handle frame are hinged bearings should be reputed make and press fitted for smooth rotation, and does not require republication i.e., maintenance - free ball bearing. seat rest is made with the lldpe sheet of with uniform bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb die supported with m.s. angle the solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and. with one year warranty., shoulder exerciser double with prime stand pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & connecting links shall be minimum of 25mm nb die of thickness not less than 3.60mm are of 'c' class heavy grade make with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the two handle frames are hinged over 100nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat & back rests are made with the lldpe with uniform bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and. with one year warranty, "ovate stepper with prime stand pipe shall be, minimum of 80mm nb dia of thickness not less than 4.50mm, pedal link pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm, handle frame pipes shall be minimum of 32mm nb dia of thickness not less than 3.60mm and handle grips shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade of with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the pedal frame are hinged over 80nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re lubrication i.e., maintenance - free ball bearing. foot rest shall be made of. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. the all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty.", "aerial stroller double with three prime stand pipes shall be minimum of 100mm nb dia of thickness not less than 5.00mm, pedestal frame shall be minimum of 32mm nb dia of thickness not less than, 3.6mm & handle frame shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade make with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the two pedestal frames are hinged over 100nb prime stand pipes with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re- lubrication i.e., maintenance -free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty", "chest press double with prime stand pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than, 3.6mm & connecting links shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns ionized coated and zinc dipped joint with robotic welded. the two handle frames are hinged over 100nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat & back rests are made with the lldpe bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle 25x25x4mm. poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and to with one year warranty", tripple twister with prime pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, standing twister plate support pipe shall be minimum of 80mm nb dia of thickness not less than 4.5mm, bottom frame support shall be minimum of 32mm nb dia of thickness not less than 3.6mm & handle ring shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the twister plate is hinged over 80nb standing pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipes with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, fore arm twirl double with centre pipe shall be of minimum 100mm nb dia of thickness not less than 5.00mm, support frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & tai chi spinner rings shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 75 microns zinc dipped joint with robotic welded with handle knobs are made from high quality nylon material. the rings are hinged over 32nb support frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed by for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 90mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, sky walker double with main frame shall be minimum of 100mm nb dia of thickness not less than 4.50mm & handle pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded with plastic/rubber grips on top end. the handle pipes are hinged over 40nb main frame with the help of especially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e. maintenance - free ball bearing. the handle pipes shall be further extended to the 24mm nb dia on both sides. paired rectangular tubes with four foot rests are linked to main frame. foot rest shall be made of aluminium material - .. all pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be deep with minimum of 100mm nb dia supported with m.s. angle the instruction plate of size of ss 304 grade plate with with your company emblem at two sides facing to users with printing. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, maintenance for open gym equipment for extra one year, providing cement concrete sitting benches including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply and delivery of 250mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., supply and delivery of 180mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., drilling of tube well with down the hole hammer drilling of finished dia meter of 165 mm dia in all formations of soils inclduing insertion of 180mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., drilling of tube well with down the hole hammer drilling of finished dia meter of 180 mm dia in all formations of soils inclduing insertion of 250mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., supply and transportation of 2.00 hp 25 stage three phase isi submersible motor pumpset suitable for 4" bore well. makes:kirloskar / crompton / texmo / cri / ksb/lubi including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-5.4.1), labour charges for fixing of submersible motors including cost of all materials and all charges etc complete, supply of 3 core 2.5 sqmm flat copper cable as per is694:1990 for submersible motors.makes: finolex / polycab / havells / v-guard / goldmedal / gm / million / vimal / nandicab / kundan cab/hi-tech including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-1.6.3) (elec-1.6.3), fabrication , transportation and supply of suitable size panel board for single phase submersible motor 2 to 3hp consisting of relay, contactor, starting and running capacitors, voltmeter, ammeter, indicator lamps, mcb , on/off switch including supply and fixing of dol starter of make c&s/l&t/seimens/bch/crompton. complete.,.including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. elec-5.4.16, manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 6kg/sqcm (vide page no-86/item no-1 of public health items of cssr - 63 mm diametre complete as per ss and as directed by the departmental officers., manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 10kg/sqcm - 63 mm diametre complete as per ss and as directed by the departmental officers., providing independent earthing by exacavating a pit to a depth of 2.25mtr in all soils as per size specified in the data for important equipment with 2.5mtr length 40mm dia 'b' class g.i pipe and 18" dia 3" thick hume pipe ring with r.c.c. slab cover duly providing staggered holes filling with 20kg salt and 40kg charcoal or 40kg bentonite powder from the bottom of the pipe giving earth connection from electrode through g.i strip of 25 x 6mm x 200mm length to be bolted with nut bolts including supply and termination of no.8 g.i.wire from bottm of the pipe with all accessories and labour charges complete, as per is specifications 732/198 and as directed by engineer incharge, fiber casting, also known as frp (fiber reinforced plastic) sculpture, is a technique where a liquid resin is poured into a mold to create a three-d object, often a statue. the process typically involves creating a clay model, taking a rubber mold, mixing resin with chalk powder and fiber liquid, pouring the mixture into the mold, and then curing and finishing the resulting fiber sculpture and including cost and conveyance of all materilas and all labour charges etc., complete as per ss and as instructed by the departmental engineer - in charge.(rabbits ,dears, budha statues ), making inauguration arrangements including cost of plaque and its fixing , chairs, shamiyanas, gralands and puja samagri and water bottles etc., operations complets as per ss.
soil filling and painting-related repair works within parks falling under the jurisdiction of hindaun city municipal council
works at the a-block park in the lalbagh neighborhood (ward no. 42), including grassing, boundary wall construction, soil filling, footpath construction, installation of gates and grilles, and painting.
providing compound wall, walking track, gym play equipment, badminton court at gollavillivanipalem park in ward.no.95 of pendurthi zone area of gvmc. - earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational incidentalm labour charges such as shoring, sheeting, planking, struting, etc, complete for finished item of work including seigniorage exclduing dewatering charges etc, per ss - 20 b (apss 308), filling with stone crusher dust in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including all operational, incidental, labour charges, seignorage charges, hire charges of t & p etc., complete for finished item of work., plain cement concrete (1:4:8) proportion (cement: fine aggregate: coarse aggregate) using 40mm size hard broken granite (is383, 1970) machine crushed metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, mixing concrete in concrete mixer including all materials, all operational, incidental, and labour charges such as laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work., brick masonry in cm (1:8) with with flyash cement solid bricks of size 290x225x140mm having a compression test not less than 50 kg/sqcm including cost and conveyance of all materials, seigniorage charges and labour charges for mixing of mortor watering curing etc. complete., plain cement concrete grade m20 - nominal mix (cement fine aggregate: coarse aggregatge) corresponding to table 9 of is 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including seignorage chargers, sales & other taxes on all materials including all operational, incidental and labour charges such as machines mixing, laying concrete, curing etc., complete as per ss, plastering in cement mortar (1:3) 12mm thick watering for curing including cost of materials, scafolding and watering and conveyance of all materials and all labour charges etc., complete as per ss and as directed by the engineer - in - charge., painting two coats with acrylic exterior emulsion paint having voc (volatile organic compound ) content less than 50 grams/ liter over plastered surface for external walls including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., supply fabrication of steel (structural) and erection of ms space frame structure with supplyting, fabricating installing the roof stucture in structural steel with necessary curvature as including cost and conveyaance, watering, tamping including all labour charges, roofing with pre-painted galvalume trapezoidal profile roofing sheets with 0.50mm thickness, coating: alu-zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness (top): 18 to 20 microns, (bottom): 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours - for dome cap type roofing fixed over the ready made steel roof structure having a bottom diametre of 36.4 metres and rise of 4.0 metres., flooring with high polished granite slabs ... mm thick other than black set over base coat of cement mortar (1:4), 20 mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like cement, sand water and tilesetc., complete, including seigniorage charges, labour charges for dressing of, formation of 150 mm thick (consolidated) walking track layer using red earth@60%,crusher dust@30% & saw dust@10% mixed thoroughly homogeneous and spreading to even surface and consolidation with hand roller and watering etc.complete finished item of work as per instructions of the department.true to uniform gradients to the possible extent., providing rcc well rings for 1.2m x 0.30m including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court poles and volley ball court poles including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court and volley ball court nylon nets including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., providing and laying of interlocking concrete block pavements of glass fibre reinforced concrete pavers of size 225 x 175 mm and thickness of not less than 60mm heavy duty conforming to is 15658:2006 including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., "malty activity play system ( special ), descriptions, ? product area : 32ft x 19ft, ? safe play area : 21ft x 42 ft, ? age group: 5-14 yrs., ? friends at a time : 15 to 18, ? platform height : 3 ft,5ft & 7f", "net rock climber 2.1 metres( pgsl 30 ), in this net rock climber pad: rock climber 7ft. pad made from fibber reinforced plastic, (frp) attached to the angular frame. the pad is provided with rock shaped part, ergonomically spaced in zigzag manner for climbing act.", "twindler go round( pgmr 01), railings: the four railings made from 15nb galvanized pipe conforming to is 1239(part, 1):1979 fixed to frp platform at one end and the other end fixed to the platform frame., platform: twindler mgr platform made from gi coated framed structure mated to fibre, reinforced plastic over the top to form a specially designed curved platform", "single board abs with centre pipe & prime, stand sleeve shall be minimum of 100mm nb dia of thickness not less than 5.00mm,footrest support & sit up board support pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm, handle frame & seat frame support shall be minimum of 24mm nb die of thickness not less than 3.6mm & connecting link pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. sit up board made with high quality frp / ss304 perforated material. all pipes shall be uniformly powder coated up to minimum 90 microns hickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed steel for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms. with one year warranty.", aero rider with main frame shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & connecting link pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the handle frame are hinged over 100nb main frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat s are made with the hdpe sheet of size. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and t. with one year warranty, hand rower with base link pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, upper link pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm & connecting links & handle links pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns ionized coated and zinc dipped joint with robotic welded. the handle frame are hinged bearings should be reputed make and press fitted for smooth rotation, and does not require republication i.e., maintenance - free ball bearing. seat rest is made with the lldpe sheet of with uniform bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb die supported with m.s. angle the solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and. with one year warranty., shoulder exerciser double with prime stand pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & connecting links shall be minimum of 25mm nb die of thickness not less than 3.60mm are of 'c' class heavy grade make with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the two handle frames are hinged over 100nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat & back rests are made with the lldpe with uniform bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and. with one year warranty, "ovate stepper with prime stand pipe shall be, minimum of 80mm nb dia of thickness not less than 4.50mm, pedal link pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm, handle frame pipes shall be minimum of 32mm nb dia of thickness not less than 3.60mm and handle grips shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade of with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the pedal frame are hinged over 80nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re lubrication i.e., maintenance - free ball bearing. foot rest shall be made of. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. the all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty.", "aerial stroller double with three prime stand pipes shall be minimum of 100mm nb dia of thickness not less than 5.00mm, pedestal frame shall be minimum of 32mm nb dia of thickness not less than, 3.6mm & handle frame shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade make with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the two pedestal frames are hinged over 100nb prime stand pipes with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re- lubrication i.e., maintenance -free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty", "chest press double with prime stand pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than, 3.6mm & connecting links shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns ionized coated and zinc dipped joint with robotic welded. the two handle frames are hinged over 100nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat & back rests are made with the lldpe bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle 25x25x4mm. poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and to with one year warranty", tripple twister with prime pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, standing twister plate support pipe shall be minimum of 80mm nb dia of thickness not less than 4.5mm, bottom frame support shall be minimum of 32mm nb dia of thickness not less than 3.6mm & handle ring shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the twister plate is hinged over 80nb standing pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipes with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, fore arm twirl double with centre pipe shall be of minimum 100mm nb dia of thickness not less than 5.00mm, support frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & tai chi spinner rings shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 75 microns zinc dipped joint with robotic welded with handle knobs are made from high quality nylon material. the rings are hinged over 32nb support frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed by for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 90mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, sky walker double with main frame shall be minimum of 100mm nb dia of thickness not less than 4.50mm & handle pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded with plastic/rubber grips on top end. the handle pipes are hinged over 40nb main frame with the help of especially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e. maintenance - free ball bearing. the handle pipes shall be further extended to the 24mm nb dia on both sides. paired rectangular tubes with four foot rests are linked to main frame. foot rest shall be made of aluminium material - .. all pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be deep with minimum of 100mm nb dia supported with m.s. angle the instruction plate of size of ss 304 grade plate with with your company emblem at two sides facing to users with printing. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, maintenance for open gym equipment for extra one year, providing cement concrete sitting benches including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply and delivery of 250mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., supply and delivery of 180mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., drilling of tube well with down the hole hammer drilling of finished dia meter of 165 mm dia in all formations of soils inclduing insertion of 180mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., drilling of tube well with down the hole hammer drilling of finished dia meter of 180 mm dia in all formations of soils inclduing insertion of 250mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., supply and transportation of 2.00 hp 25 stage three phase isi submersible motor pumpset suitable for 4" bore well. makes:kirloskar / crompton / texmo / cri / ksb/lubi including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-5.4.1), labour charges for fixing of submersible motors including cost of all materials and all charges etc complete, supply of 3 core 2.5 sqmm flat copper cable as per is694:1990 for submersible motors.makes: finolex / polycab / havells / v-guard / goldmedal / gm / million / vimal / nandicab / kundan cab/hi-tech including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-1.6.3) (elec-1.6.3), fabrication , transportation and supply of suitable size panel board for single phase submersible motor 2 to 3hp consisting of relay, contactor, starting and running capacitors, voltmeter, ammeter, indicator lamps, mcb , on/off switch including supply and fixing of dol starter of make c&s/l&t/seimens/bch/crompton. complete.,.including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. elec-5.4.16, manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 6kg/sqcm (vide page no-86/item no-1 of public health items of cssr - 63 mm diametre complete as per ss and as directed by the departmental officers., manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 10kg/sqcm - 63 mm diametre complete as per ss and as directed by the departmental officers., providing independent earthing by exacavating a pit to a depth of 2.25mtr in all soils as per size specified in the data for important equipment with 2.5mtr length 40mm dia 'b' class g.i pipe and 18" dia 3" thick hume pipe ring with r.c.c. slab cover duly providing staggered holes filling with 20kg salt and 40kg charcoal or 40kg bentonite powder from the bottom of the pipe giving earth connection from electrode through g.i strip of 25 x 6mm x 200mm length to be bolted with nut bolts including supply and termination of no.8 g.i.wire from bottm of the pipe with all accessories and labour charges complete, as per is specifications 732/198 and as directed by engineer incharge, making inauguration arrangements including cost of plaque and its fixing , chairs, shamiyanas, gralands and puja samagri and water bottles etc., operations complets as per ss.
corrigendum : repair to floor, plinth, plaster, roof sheeting, earth filling, joinery etc and maint of grass cutting and earth filling in wsa in tech area at af stn halwara
corrigendum : repair to drain, path, toe walls, earth filling and other allied services at wsa-i,ii and provn of smart periodical services to certain md accn at vayu vihar at af stn adampur
construction of new building for janakeeya arogya kendram konghal at kollam district - this work consists of construction earth work in excavation, random block masonry, reinforced cement concrete, centering and shuttering, steel reinforcement for r.c.c work, aluminium work for doors, windows, ventilators,ceramic
corrigendum : provn of earth filling at blast pen at bhisiana under ge (af) bhisiana
providing walking track play equipment, badminton court at prasad nagar in ward.no.96 of pendurthi zone area of gvmc - earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational incidentalm labour charges such as shoring, sheeting, planking, struting, etc, complete for finished item of work including seigniorage exclduing dewatering charges etc, per ss - 20 b (apss 308), filling with stone crusher dust in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including all operational, incidental, labour charges, seignorage charges, hire charges of t & p etc., complete for finished item of work., plain cement concrete (1:4:8) proportion (cement: fine aggregate: coarse aggregate) using 40mm size hard broken granite (is383, 1970) machine crushed metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, mixing concrete in concrete mixer including all materials, all operational, incidental, and labour charges such as laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work., collection of gravel from approved quarry including cost, conveyance and seignerage charges including, stacking at site to departmental gauge spreading, sectioning with rolling charges etc complete - 1 cum, brick masonry in cm (1:8) with with flyash cement solid bricks of size 290x225x140mm having a compression test not less than 50 kg/sqcm including cost and conveyance of all materials, seigniorage charges and labour charges for mixing of mortor watering curing etc. complete., plastering in cement mortar (1:3) 12mm thick watering for curing including cost of materials, scafolding and watering and conveyance of all materials and all labour charges etc., complete as per ss and as directed by the engineer - in - charge., painting two coats with acrylic exterior emulsion paint having voc (volatile organic compound ) content less than 50 grams/ liter over plastered surface for external walls including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., supply fabrication of steel (structural) and erection of ms space frame structure with supplyting, fabricating installing the roof stucture in structural steel with necessary curvature as including cost and conveyaance, watering, tamping including all labour charges, roofing with pre-painted galvalume trapezoidal profile roofing sheets with 0.50mm thickness, coating: alu-zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness (top): 18 to 20 microns, (bottom): 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours - for dome cap type roofing fixed over the ready made steel roof structure having a bottom diametre of 36.4 metres and rise of 4.0 metres., flooring with high polished granite slabs ... mm thick other than black set over base coat of cement mortar (1:4), 20 mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like cement, sand water and tilesetc., complete, including seigniorage charges, labour charges for dressing of, formation of 150 mm thick (consolidated) walking track layer using red earth@60%,crusher dust@30% & saw dust@10% mixed thoroughly homogeneous and spreading to even surface and consolidation with hand roller and watering etc.complete finished item of work as per instructions of the department.true to uniform gradients to the possible extent., providing rcc well rings for 1.2m x 0.30m including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court poles and volley ball court poles including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court and volley ball court nylon nets including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., "malty activity play system ( special ), descriptions, ? product area : 32ft x 19ft, ? safe play area : 21ft x 42 ft, ? age group: 5-14 yrs., ? friends at a time : 15 to 18, ? platform height : 3 ft,5ft & 7f", "net rock climber 2.1 metres( pgsl 30 ), in this net rock climber pad: rock climber 7ft. pad made from fibber reinforced plastic, (frp) attached to the angular frame. the pad is provided with rock shaped part, ergonomically spaced in zigzag manner for climbing act.", fiber casting, also known as frp (fiber reinforced plastic) sculpture, is a technique where a liquid resin is poured into a mold to create a three-d object, often a statue. the process typically involves creating a clay model, taking a rubber mold, mixing resin with chalk powder and fiber liquid, pouring the mixture into the mold, and then curing and finishing the resulting fiber sculpture and including cost and conveyance of all materilas and all labour charges etc., complete as per ss and as instructed by the departmental engineer - in charge.(rabbits ,dears, budha statues ), "twindler go round( pgmr 01), railings: the four railings made from 15nb galvanized pipe conforming to is 1239(part, 1):1979 fixed to frp platform at one end and the other end fixed to the platform frame., platform: twindler mgr platform made from gi coated framed structure mated to fibre, reinforced plastic over the top to form a specially designed curved platform", providing cement concrete sitting benches including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., providing independent earthing by exacavating a pit to a depth of 2.25mtr in all soils as per size specified in the data for important equipment with 2.5mtr length 40mm dia 'b' class g.i pipe and 18" dia 3" thick hume pipe ring with r.c.c. slab cover duly providing staggered holes filling with 20kg salt and 40kg charcoal or 40kg bentonite powder from the bottom of the pipe giving earth connection from electrode through g.i strip of 25 x 6mm x 200mm length to be bolted with nut bolts including supply and termination of no.8 g.i.wire from bottm of the pipe with all accessories and labour charges complete, as per is specifications 732/198 and as directed by engineer incharge, making inauguration arrangements including cost of plaque and its fixing , chairs, shamiyanas, gralands and puja samagri and water bottles etc., operations complets as per ss.
providing walking track, gym, play equipment, badminton court at mes layout park in ward.no.97 of pendurthi zone area of gvmc - earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational incidentalm labour charges such as shoring, sheeting, planking, struting, etc, complete for finished item of work including seigniorage exclduing dewatering charges etc, per ss - 20 b (apss 308), engaging of front end loader for jungle clearnace and including cost and conveyance of all materials and labour charges as per ss and as directed by the department officers, engaging of tipper for conveynace of debries and waste materials from site to dummping yard etc., complete as per ss and as directed by the dept. officer, filling with stone crusher dust in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including all operational, incidental, labour charges, seignorage charges, hire charges of t & p etc., complete for finished item of work., plain cement concrete (1:4:8) proportion (cement: fine aggregate: coarse aggregate) using 40mm size hard broken granite (is383, 1970) machine crushed metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, mixing concrete in concrete mixer including all materials, all operational, incidental, and labour charges such as laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work., providing high yield strength deformed (hysd) steel bars (fe 415 grade as per is 1786-1979) of different diameters for rcc works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lapsplicing with binding wire of 18 swg, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, laour charges such as cutting, bending placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (apss no.126), vibrated reinfrced cement concrete m30 design mix grade corresponding to is 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyane of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work (apss.no.402) with 400kg/cum cement from standard suppliers approved by the department including centering, shuttering, laying concrete, vibrating, curing etc., complete, for entrance gate pedastal (footings, for columns, for plinth beam, brick masonry in cm (1:8) with with flyash cement solid bricks of size 290x225x140mm having a compression test not less than 50 kg/sqcm including cost and conveyance of all materials, seigniorage charges and labour charges for mixing of mortor watering curing etc. complete., plain cement concrete grade m20 - nominal mix (cement fine aggregate: coarse aggregatge) corresponding to table 9 of is 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including seignorage chargers, sales & other taxes on all materials including all operational, incidental and labour charges such as machines mixing, laying concrete, curing etc., complete as per ss, plastering in cement mortar (1:3) 12mm thick watering for curing including cost of materials, scafolding and watering and conveyance of all materials and all labour charges etc., complete as per ss and as directed by the engineer - in - charge., painting two coats with acrylic exterior emulsion paint having voc (volatile organic compound ) content less than 50 grams/ liter over plastered surface for external walls including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., supply fabrication of steel (structural) and erection of ms space frame structure with supplyting, fabricating installing the roof stucture in structural steel with necessary curvature as including cost and conveyaance, watering, tamping including all labour charges, painting with synthetic enamel paint -two coats - for new iron work over a primer of zinc chromate yellow oxide including cost and conveyance of all materials and labour charges as per ss and as directed by the department officers, providing rcc well rings for 1.2m x 0.30m including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court poles and volley ball court poles including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply, delivery and fixing of badminton court and volley ball court nylon nets including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., providing and laying of interlocking concrete block pavements of glass fibre reinforced concrete pavers of size 225 x 175 mm and thickness of not less than 60mm heavy duty conforming to is 15658:2006 including cost & conveyance of all materials and all labour charges etc complete as per ss and as directed by the department officers., "malty activity play system ( special ), descriptions, ? product area : 32ft x 19ft, ? safe play area : 21ft x 42 ft, ? age group: 5-14 yrs., ? friends at a time : 15 to 18, ? platform height : 3 ft,5ft & 7f", "single board abs with centre pipe & prime, stand sleeve shall be minimum of 100mm nb dia of thickness not less than 5.00mm,footrest support & sit up board support pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm, handle frame & seat frame support shall be minimum of 24mm nb die of thickness not less than 3.6mm & connecting link pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. sit up board made with high quality frp / ss304 perforated material. all pipes shall be uniformly powder coated up to minimum 90 microns hickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed steel for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms. with one year warranty.", aero rider with main frame shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & connecting link pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the handle frame are hinged over 100nb main frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. seat s are made with the hdpe sheet of size. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and t. with one year warranty, hand rower with base link pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, upper link pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm & connecting links & handle links pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns ionized coated and zinc dipped joint with robotic welded. the handle frame are hinged bearings should be reputed make and press fitted for smooth rotation, and does not require republication i.e., maintenance - free ball bearing. seat rest is made with the lldpe sheet of with uniform bending radius to avoid sharp edges. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb die supported with m.s. angle the solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms and. with one year warranty., "ovate stepper with prime stand pipe shall be, minimum of 80mm nb dia of thickness not less than 4.50mm, pedal link pipe shall be minimum of 50mm nb dia of thickness not less than 4.1mm, handle frame pipes shall be minimum of 32mm nb dia of thickness not less than 3.60mm and handle grips shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade of with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the pedal frame are hinged over 80nb prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re lubrication i.e., maintenance - free ball bearing. foot rest shall be made of. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. the all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty.", "aerial stroller double with three prime stand pipes shall be minimum of 100mm nb dia of thickness not less than 5.00mm, pedestal frame shall be minimum of 32mm nb dia of thickness not less than, 3.6mm & handle frame shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade make with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded. the two pedestal frames are hinged over 100nb prime stand pipes with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re- lubrication i.e., maintenance -free ball bearing. all pipes shall be uniformly powder coated up to minimum 90 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle. all plastic parts should solid poly propylene co-polymer (ppcp) and uv- stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty", sky walker double with main frame shall be minimum of 100mm nb dia of thickness not less than 4.50mm & handle pipes shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of 'c' class heavy grade with hot dipped galvanised with minimum of 60 microns zinc dipped joint with robotic welded with plastic/rubber grips on top end. the handle pipes are hinged over 40nb main frame with the help of especially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e. maintenance - free ball bearing. the handle pipes shall be further extended to the 24mm nb dia on both sides. paired rectangular tubes with four foot rests are linked to main frame. foot rest shall be made of aluminium material - .. all pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be closed for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be deep with minimum of 100mm nb dia supported with m.s. angle the instruction plate of size of ss 304 grade plate with with your company emblem at two sides facing to users with printing. all plastic parts should solid poly propylene co-polymer (ppcp) and uv stabilized should be used. all products of equipment should be manufactured as per en 16630 safety norms with one year warranty, maintenance for open gym equipment for extra one year, providing cement concrete sitting benches including cost and conveyaance, watering, tamping including all labour charges etc., complete as per ss and as directed by the engineer - in - charge., supply and delivery of 250mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., supply and delivery of 180mm pvc casing pipe 6 kg /cmsq (finolex/prince/sudhakar) manufacture, supply and delivery of unplasticised pvcs pipes for potable water supplies conforming to is : 4985/2000 (3rd revision) with bell ends (socket) as per specification in light grey/natural ivory grey/ any other color (except white) inclusive of transportation to the sub-divisional storesanywhere in ap excluding excise duty and sales tax etc., drilling of tube well with down the hole hammer drilling of finished dia meter of 165 mm dia in all formations of soils inclduing insertion of 180mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., drilling of tube well with down the hole hammer drilling of finished dia meter of 180 mm dia in all formations of soils inclduing insertion of 250mm dia pvc casing pipe of 6kg/cm2 of isi make and providing cap as directed by the departmental officer and transporation of drilling equipment and supporting vehicle etc., complete but excluding cost of pvc casing pipe etc., complete as per ss and as directed by the departmental officers., supply and transportation of 2.00 hp 25 stage three phase isi submersible motor pumpset suitable for 4" bore well. makes:kirloskar / crompton / texmo / cri / ksb/lubi including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-5.4.1), labour charges for fixing of submersible motors including cost of all materials and all charges etc complete, supply of 3 core 2.5 sqmm flat copper cable as per is694:1990 for submersible motors.makes: finolex / polycab / havells / v-guard / goldmedal / gm / million / vimal / nandicab / kundan cab/hi-tech including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. (elec-1.6.3) (elec-1.6.3), fabrication , transportation and supply of suitable size panel board for single phase submersible motor 2 to 3hp consisting of relay, contactor, starting and running capacitors, voltmeter, ammeter, indicator lamps, mcb , on/off switch including supply and fixing of dol starter of make c&s/l&t/seimens/bch/crompton. complete.,.including cost and conveyance of all materilas and all labour charges etc complete as per ss and as directed by the departmental officers. elec-5.4.16, manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 6kg/sqcm (vide page no-86/item no-1 of public health items of cssr - 63 mm diametre complete as per ss and as directed by the departmental officers., manufacture, supply, & delivery of hdpe pipes conforming to is 4984 - 1995 including transportation to any where in a.p, including excise duty, sale tax and specials etc., complete. p.e.100 grade 10kg/sqcm - 63 mm diametre complete as per ss and as directed by the departmental officers., making inauguration arrangements including cost of plaque and its fixing , chairs, shamiyanas, gralands and puja samagri and water bottles etc., operations complets as per ss.
co ns. of plwss from kurpan khad to gp ghatoo gamog and shilli in nirmand block distt. kullu (h.p) - sh excavation in foundation trenches etc. in earth work laying jointing and testing of g.i. pipe 150 mm dia (mc) rd 0 to 950. 950 rmt. for with butt welding (for gravity main) laying jointing and testing of gi pipe 80 mm dia (lc) 800 rmt 65 mm
LOADING...
LOADING...